Environmental Permit No. EP-226/2005/G
Àô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/G
ENVIRONMENTAL IMPACT ASSESSMENT
ORDINANCE
(CHAPTER 499)
SECTIONS 10 & 13
Àô¹Ò¼vÅTµû¦ô±ø¨Ò
(²Ä499³¹)
²Ä10¤Î13±ø
ENVIRONMENTAL PERMIT TO CONSTRUCT AND OPERATE
A DESIGNATED PROJECT
«Ø³y¤ÎÀç¿ì«ü©w¤uµ{¶µ¥ØªºÀô¹Ò³\¥iÃÒ
A³¡ (³\¥iÃÒ¥Dn³¡¤À)
Pursuant
to Section 10 of the Environmental Impact Assessment Ordinance (EIAO), the Director
of Environmental Protection (the Director) granted the Environmental Permit
(No. EP-226/2005) to the DIRECTOR OF
ENVIRONMENTAL PROTECTION (hereinafter
referred to as the ¡§Permit Holder¡¨) on 9 September 2005. Pursuant
to Section 13 of the EIAO, the Director amends the Environmental Permit (No.
EP-226/2005/F) based on the
Application No. VEP-588/2021. The amendments
described below are incorporated into this Environmental Permit (No.
EP-226/2005/G). This
Environmental Permit as amended is for the construction and operation of the
designated project described in Part B of this
Permit subject to the conditions specified in and attached to Part C of this Permit.
®Ú¾Ú¡mÀô¹Ò¼vÅTµû¦ô±ø¨Ò¡n(Àôµû±ø¨Ò)
²Ä10±øªº³W©w¡AÀô¹Ò«OÅ@¸p¸pªø(¸pªø)©ó
The issue of this amended
Environmental Permit is based on the documents, approvals or permissions
described below:
¥»¸g×qªºÀô¹Ò³\¥iÃÒ¬O¨Ì¾Ú¤U¦C¤å¥ó¡B§åã©Î³\¥i¦Óñµo¡R
Application No. ¥Ó½Ð®Ñ½s¸¹ |
VEP-588/2021 |
Documents in the Register: µn°O¥U¤Wªº¤å¥ó¡G |
(1)
Development of an EcoPark in Tuen Mun Area 38:
Environmental Impact Assessment (EIA) Report, Environmental Monitoring and
Audit (EM&A) Manual and Executive Summary (Register
No.: AEIAR-086/2005) [Hereinafter referred to as the ¡§EIA Report¡¨] (1)
©ó¤Ùªù38°Ïµo®iÀô«O¶é¡GÀô¹Ò¼vÅTµû¦ô³ø§i¡BÀô¹ÒºÊ¹î¤Î¼f®Ö¤â¥U¤Î¦æ¬FºKn (µn°O¥U½s¸¹¡GAEIAR-086/2005) [¤UºÙ ¡§Àôµû³ø§i¡¨] |
Documents in the Register: µn°O¥U¤Wªº¤å¥ó¡G |
(2)
The Director¡¦s letter of approval
of the EIA Report dated 29 June 2005 (Reference: (31) in Ax(14) to
EP2/N4/G/34 III) (2) ¸pªø©ó (3)
Application for Environmental
Permit submitted by the Permit Holder on 11 August 2005 (Application No.
AEP-226/2005) (3)
³\¥iÃÒ«ù¦³¤H©ó (4)
Environmental Permit (Permit No.
EP-226/2005) issued on 9 September 2005 (4)
©ó (5)
Application
for Variation of an Environmental Permit including all attachments submitted
by the Permit Holder on 1 August 2006 (Application No. VEP-221/2006) (5)
³\¥iÃÒ«ù¦³¤H©ó (6)
Environmental Permit (Permit No.
EP-226/2005/A) issued on 28 August 2006 (6)
©ó (7)
Application
for Variation of an Environmental Permit including all attachments submitted by
the Permit Holder on 23 May 2013 (Application No. VEP-405/2013) (7)
³\¥iÃÒ«ù¦³¤H©ó (8)
Environmental Permit (Permit No.
EP-226/2005/B) issued on 21 June 2013 (8)
©ó (9)
Application
for Variation of an Environmental Permit including all attachments submitted
by the Permit Holder on 8 July 2013 (Application No. VEP-408/2013) (9)
³\¥iÃÒ«ù¦³¤H©ó (10)
Environmental
Permit (Permit No. EP-226/2005/C)
issued on 5
August
2013 (10)
©ó2013¦~8¤ë5¤éµo¥XªºÀô¹Ò³\¥iÃÒ(³\¥iÃÒ½s¸¹¡GEP-226/2005/C) (11)
Application
for Variation of an Environmental Permit including all attachments submitted
by the Permit Holder on 2
February 2016 (Application No. VEP-494/2016) (11) ³\¥iÃÒ«ù¦³¤H©ó2016¦~2¤ë2¤é´£¥æªº§ó§ïÀô¹Ò³\¥iÃҥӽХ]¬A©Ò¦³ªþ¥ó¡]¥Ó½Ð®Ñ½s¸¹¡GVEP-494/2016¡^ (12)
Environmental
Permit (Permit No. EP-226/2005/D)
issued on 24
February 2016 (12)
©ó2016¦~2¤ë24¤éµo¥XªºÀô¹Ò³\¥iÃÒ(³\¥iÃÒ½s¸¹¡GEP-226/2005/D) (13)
Application
for Variation of an Environmental Permit including all attachments submitted
by the Permit Holder on 14
August 2017 (Application No. VEP-532/2017) (13) ³\¥iÃÒ«ù¦³¤H©ó2017¦~8¤ë14¤é´£¥æªº§ó§ïÀô¹Ò³\¥iÃҥӽХ]¬A©Ò¦³ªþ¥ó(¥Ó½Ð®Ñ½s¸¹¡GVEP-532/2017¡^ (14) Environmental Permit (Permit No.
EP-226/2005/E)
issued on
7 September 2017 (14) ©ó2017¦~9¤ë7¤éµo¥XªºÀô¹Ò³\¥iÃÒ(³\¥iÃÒ½s¸¹¡GEP-226/2005/E (15) Application for Variation of an Environmental
Permit including all attachments submitted by the Permit Holder on 11 September 2018 (Application No. VEP-548/2018) (15) ³\¥iÃÒ«ù¦³¤H©ó2018¦~9¤ë11¤é´£¥æªº§ó§ïÀô¹Ò³\¥iÃҥӽХ]¬A©Ò¦³ªþ¥ó(¥Ó½Ð®Ñ½s¸¹¡GVEP-548/2018) (16) Environmental Permit (Permit No.
EP-226/2005/F)
issued on
7 September 2017 (16) ©ó2018¦~9¤ë20¤éµo¥XªºÀô¹Ò³\¥iÃÒ(³\¥iÃÒ½s¸¹¡GEP-226/2005/F (17) Application for Variation of an
Environmental Permit including all attachments submitted by the Permit Holder
on 24 February 2021
(Application No. VEP-588/2021) (17) ³\¥iÃÒ«ù¦³¤H©ó2021¦~2¤ë24¤é´£¥æªº§ó§ïÀô¹Ò³\¥iÃҥӽХ]¬A©Ò¦³ªþ¥ó(¥Ó½Ð®Ñ½s¸¹¡GVEP-588/2021) |
Application No. ¥Ó½Ð®Ñ½s¸¹ |
Date of Application ¥Ó½Ð¤é´Á |
List of Amendments Incorporated into this Environmental Permit ¤w¥]§t¦b¥»Àô¹Ò³\¥iÃÒ¤ºªº×q¶µ¥Ø |
Date of Amendment ×q¤é´Á |
VEP-221/2006 |
1 August 2006 |
-
Vary
Condition -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005 C³¡ªº²Ä3.7¶µ±ø¥ó -
Vary Figure 3 of the Environmental Permit No.
EP-226/2005 -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005 ªº¹Ï3 |
28 August
2006 |
VEP-405/2013 |
23 May 2013 |
-
Vary
Annex A in Part C of the Environmental Permit No.
EP-226/2005/A -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/A C³¡¤Îªþ¥óA -
Add
Condition 4.15, Annex C and Figure -
¦bÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/A C³¡¥[¤J²Ä4.15¶µ±ø¥ó,ªþ¥óC ¤Î¹Ï5 (¾A¥Î©ó¦¬¶°¼o¹q¦À¥H¦^¦¬¹]ªº¼t©Ð) |
21 June 2013 |
VEP-408/2013 |
8 July 2013 |
-
Add
Condition 4.16, Annex D, E and Figure 6 in Part C of the
Environmental Permit No. EP-226/2005/B (for a plant collecting Waste
Electrical and Electronic Equipment) -
¦bÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/B C³¡¥[¤J²Ä4.16¶µ±ø¥ó,ªþ¥óD,E ¤Î¹Ï6 (¾A¥Î©ó¦¬¶°¼o¹q¾¹¹q¤l²£«~ªº¼t©Ð) |
5 August
2013 |
VEP-494/2016 |
2 February 2016 2016¦~2¤ë2¤é |
-
Vary Annex C of Environmental Permit No. EP-226/2005/C, Item i c),
d), g), h), j), l), m), n), p) and q) -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/Cªþ¥óC±ø¥ói ²Äc), d), g), h), j), l), m), n), p)¤Îq)¶µ -
Delete Annex C of Environmental Permit No.
EP-226/2005/C, Item i r)
s) and t) -
§R°£Àô¹Ò³\¥iÃÒ½sEP-226/2005/Cªþ¥óC±ø¥ói ²Är), s)¤Ît)¶µ -
Vary Figure 5 of Environmental Permit No.
EP-226/2005/C -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹EP-226/2005/Cªº¹Ï5 |
24 February 2016 2016¦~2¤ë24¤é |
VEP-532/2017 |
14 August 2017 2017¦~8¤ë14¤é |
-
Vary Annex E of Environmental Permit No. EP-226/2005/D, -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/Dªþ¥óE |
7 September 2017 2017¦~9¤ë7¤é |
VEP-548/2018 |
11 September 2018 2018¦~9¤ë11 ¤é |
-
Vary Conditions 4.4 and 5.3 in Part C of the Environmental Permit No. EP-226/2005/E -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/E C³¡ªº²Ä4.4¤Î5.3¶µ±ø¥ó |
20 September
2018 2018¦~9¤ë20¤é |
VEP-588/2021 |
24 February
2021 2021¦~2¤ë24¤é |
-
Vary Annex B, Annex E and Figure 3 in Part C
of the Environmental Permit No. EP-226/2005/F -
§ó§ïÀô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/F C³¡ªºªþ¥óB, ªþ¥óE¤Î¹Ï3 -
Add
Condition
4.17 and Annex F in Part C of the Environmental Permit No. EP-226/2005/F (for a
plant collecting waste paper) -
¦bÀô¹Ò³\¥iÃÒ½s¸¹
EP-226/2005/F C³¡¥[¤J²Ä4.17¶µ±ø¥ó¤Îªþ¥óF (¾A¥Î©ó¦¬¶°¼o¯Èªº¼t©Ð) |
18 March 2021 2021¦~3¤ë18¤é |
18 March 2021
2021¦~3¤ë18 ¤é
Date ¤é´Á |
|
(Stanley C. F. LAU) Acting Principal Environmental
Protection Officer for Director of Environmental
Protection Àô¹Ò«OÅ@¸p¸pªø
(¸p²zº®uÀô¹Ò«OÅ@¥D¥ô¼B§Ó½÷¥N¦æ) |
PART B (DESCRIPTIONS OF DESIGNATED PROJECT)
B³¡ («ü©w¤uµ{¶µ¥Øªº»¡©ú)
Hereunder is the description of the designated
project mentioned in Part A of this Environmental
Permit (hereinafter referred to as the ¡§Permit¡¨):
¤U¦C¬°¥»Àô¹Ò³\¥iÃÒ(¤UºÙ¡§³\¥iÃÒ¡¨)A³¡©Ò´£¤Îªº«ü©w¤uµ{¶µ¥Øªº»¡©ú:
Title
of Designated Project «ü©w¤uµ{¶µ¥Øªº¦WºÙ |
Development of an EcoPark in Tuen Mun Area 38 [This designated project is hereinafter referred
to as ¡§the Project¡¨] ©ó¤Ùªù38°Ïµo®iÀô«O¶é [¥»«ü©w¤uµ{¶µ¥Ø¤UºÙ ¡§¤uµ{¶µ¥Ø¡¨] |
Nature of Designated Project |
To construct and operate waste disposal
facilities or carry out waste disposal activities for various wastes
including chemical and industrial wastes. ¬°¤£¦Pªº¼oª«¥]¬A¤Æ¾Ç¼oª«©M¤u·~¼oª«¦Ó«Ø³y¤ÎÀç¿ì¼oª«³B¸m³]¬I©Î¶i¦æ¼oª«³B¸m¬¡°Ê¡C |
Location
of Designated Project «ü©w¤uµ{¶µ¥Øªº¦aÂI |
Area 38 of Tuen Mun. The
location of the Project (Phase I and Phase II) is shown in Figure 1 attached to this Permit. ¤Ùªù²Ä38°Ï¡C¤uµ{¶µ¥Ø(²Ä¤@´Á¤Î²Ä¤G´Á)ªº¦ì¸m¸ü©ó¥»³\¥iÃÒ§¨ªþªº¹Ï1¡C |
Scale and Scope of Designated Project «ü©w¤uµ{¶µ¥Øªº³W¼Ò©M½d³ò |
Construction
and operation of an EcoPark in Tuen Mun Area 38 for recycling of materials
which involves waste disposal facilities or waste disposal activities for
various wastes including chemical and industrial wastes. (See Annex E for total annual throughput limits for different
material type) ©ó¤Ùªù38°Ï«Ø³y¤ÎÀç¿ìÀô«O¶é¥Î§@ª«®Æ¦^¦¬¦A³y¡A¨ä¤¤·|¬°¤£¦Pªº¼oª«¥]¬A¤Æ¾Ç¼oª«©M¤u·~¼oª«³]¸m¼oª«³B¸m³]¬I©Î¶i¦æ¼oª«³B¸m¬¡°Ê¡C (½Ð°Ñ¾\ªþ¥óEªº¤£¦Pª«®ÆºØÃþªº¨C¦~Á`¥Í²£¶qªº¨î) |
C³¡ (³\¥iÃÒ±ø¥ó)
1. General
Conditions
¤@¯ë±ø¥ó
1.1 The Permit Holder and any
person working on the Project shall comply with all conditions set out in this
Permit. Any non-compliance by any person may constitute a contravention of the Environmental
Impact Assessment Ordinance (EIAO) (Cap. 499) and may become the subject of
appropriate action being taken under the EIAO.
³\¥iÃÒ«ù¦³¤H¤Î¥ô¦ó±q¨Æ¤uµ{¶µ¥Øªº¤H¤h¥²¶·²Å¦X¥»³\¥iÃÒ¸ü¦Cªº¥þ³¡±ø¥ó¡C¥ô¦ó¤H¤h¦p¦³¤£²Å¦X¥»³\¥iÃÒªº±¡ªp¡A¥i¯à¹H¤ÏÀô¹Ò¼vÅTµû¦ô±ø¨Ò (¡uÀôµû±ø¨Ò¡v) (²Ä499³¹) ªº³W©w¡A¦Ó·í§½¥i®Ú¾ÚÀôµû±ø¨Ò±Ä¨ú¾A·í¦æ°Ê¡C
1.2 The Permit Holder shall ensure
full compliance with all legislation from time to time in force including,
without limitation to, the Air Pollution Control Ordinance (Cap. 311), Waste
Disposal Ordinance (Cap. 354), Water Pollution Control Ordinance (Cap. 358),
Noise Control Ordinance (Cap. 400), Dumping at Sea Ordinance (Cap. 466), Occupational Safety and Health
Ordinance (Cap.509), Factories and Industrial Undertakings Ordinance (Cap.59)
and Dangerous Goods Ordinance (Cap.295).
This Permit does not of itself constitute any ground of defence against any
proceedings instituted under any legislation or imply any approval under any
legislation.
³\¥iÃÒ«ù¦³¤H¶·¸g±`½T«O§¹¥þ²Å¦X²{¦æªk¨Òªº³W©w¡A¥]¬A¦ý¤£©óªÅ®ð¦Ã¬VºÞ¨î±ø¨Ò (²Ä311³¹)¡F¼oª«³B¸m±ø¨Ò (²Ä354³¹)¡F¤ô¦Ã¬VºÞ¨î±ø¨Ò (²Ä358³¹)¡F¾¸µºÞ¨î±ø¨Ò (²Ä400³¹)¡F®ü¤W¶É˪«®Æ±ø¨Ò (²Ä466³¹)¡F¾·~¦w¥þ¤Î°·±d±ø¨Ò (²Ä509³¹)¡F¤u¼t¤Î¤u·~¸gÀç±ø¨Ò (²Ä59³¹)©M¦MÀIª««~±ø¨Ò (²Ä295³¹)¡C¥»³\¥iÃÒ¥»¨¤£·|´N®Ú¾Ú¥ô¦óªk¨Ò´£°_ªºªk«ßµ{§Çºc¦¨¥ô¦ó§ÜÅG²z¥Ñ¡A©Î®Ú¾Ú¥ô¦óªk¨ÒÀq¥Ü¥ô¦ó§åã¡C
1.3 The Permit Holder shall make
copies of this Permit together with all documents referred to in this Permit or
the documents referred to in Part A of the Permit
readily available at all times for inspection by the Director or his authorised
officers at all sites/offices covered by this Permit. Any reference to the
Permit shall include all documents referred to in the Permit and also the relevant
documents in the Register.
³\¥iÃÒ«ù¦³¤H¶·¦L»s¥»³\¥iÃÒªº½Æ¥»¡A³s¦P¥»³\¥iÃÒ©Òzªº©Ò¦³¤å¥ó©Î¥»³\¥iÃÒA³¡©Òz¤å¥ó¡A¥H¨Ñ¸pªø©ÎÀò±ÂÅv¤Hû¥ô¦ó®É¶¡¤º¦b¥»³\¥iÃÒ©Ò²[»\ªº©Ò¦³¤u¦a / ¿ì¨Æ³B¬d¾\¡C¤Z´£z¥»³\¥iÃÒ¡A¶·¥]¬A¥»³\¥iÃÒ©Òzªº©Ò¦³¤å¥ó¤Îµn°O¥U¤ºªº¬ÛÃö¤å¥ó¡C
1.4 The Permit Holder shall give a
copy of this Permit to the person(s) in charge of the site(s) and ensure that
such person(s) fully understands all conditions and all requirements
incorporated by the Permit. The site(s) refers to site(s) of construction and
operation of the Project and shall mean the same hereafter.
³\¥iÃÒ«ù¦³¤H¶·§â¥»³\¥iÃÒªº½Æ¥»¥æ¤©¦³Ãö¤u¦aªºt³d¤H¡A¨Ã½T«O³o¨Ç¤H¤h§¹¥þ©ú¥Õ¥»³\¥iÃÒªº©Ò¦³±ø¥ó»P³W©w¡C¤u¦a¬O«ü«Ø³y¤ÎÀç¿ì¤uµ{¶µ¥Øªº¤u¦a¡A¤U¤å©Ò´£¤Îªº¤u¦a¥çÄݦP¤@·N«ä¡C
1.5 The Permit Holder shall display
conspicuously a copy of this Permit on the Project site(s) at all vehicular
site entrances/exits or at a convenient location for public¡¦s information at
all times. The Permit Holder shall ensure that the most updated information
about the Permit, including any amended Permit, is displayed at such
locations. If the Permit Holder surrenders a part or the whole of the
Permit, the notice he sends to the Director shall also be displayed at the same
locations as the original Permit. The suspended, varied or cancelled
Permit shall be removed from display at the Project site(s).
³\¥iÃÒ«ù¦³¤H¶·¦b¤uµ{¶µ¥Øªº¤u¦aªº©Ò¦³¨®½ø¶i¥X¤f©Î¤@³B¤è«K¦aÂI¡AÅã²´¦a®i¥Ü¥»³\¥iÃÒªº½Æ¥»¡A¥H¨Ñ¤½²³¦b¥ô¦ó®É¶¡¤º¾\Äý¡C³\¥iÃÒ«ù¦³¤H¶·½T«O¦b³o¨Ç¦aÂI®i¥ÜÃö©ó¥»³\¥iÃÒ (¥]¬A¥ô¦ó¸g×qªº³\¥iÃÒ) ªº³Ì·s¸ê®Æ¡C³\¥iÃÒ«ù¦³¤H¦p¥æ¦^³\¥iÃÒªº³¡¤À©Î¥þ³¡¡A¥²¶·§â¨ä°e¥æ¸pªøªº³qª¾®Ñ¡A¦b³Æ¦³ì¦³³\¥iÃÒªº¬Û¦P¦aÂI®i¥Ü¡C¾D¼È®É¦Q¾P¡B§ó§ï©Î¨ú®øªº³\¥iÃÒ¥²¶·±q¤uµ{¶µ¥Øªº¤u¦a°£¤U¡A¤£¦A®i¥Ü¡C
1.6 The Permit Holder shall
construct and operate the Project in accordance with the project descriptions
in Part B of this Permit.
³\¥iÃÒ«ù¦³¤H¶·¨Ì¾Ú¥»³\¥iÃÒB³¡ªº¤uµ{¶µ¥Ø»¡©ú¡A«Ø³y¤ÎÀç¿ì¤uµ{¶µ¥Ø¡C
1.7 The
Permit Holder shall ensure that the Project is designed, constructed and
operated in accordance with the information and all recommendations described
in the EIA Report (Register No.: AEIAR-086/2005), the application documents
including all attachments (Applications No. AEP-226/2005, VEP-221/2006,
VEP-405/2013, VEP-408/2013 and
VEP-494/2016), other relevant documents in the
Register; and the information or mitigation measures described in this Permit,
and mitigation measures to be recommended in submissions that shall be
deposited with or approved by the Director as a result of permit conditions
contained in this Permit, and mitigation measures to be recommended under on
going surveillance and monitoring activities during all stages of the Project.
Where recommendations referred to in the documents of the Register are not
expressly referred to in this Permit, such recommendations are nevertheless to
be implemented unless expressly excluded or impliedly amended in this Permit.
³\¥iÃÒ«ù¦³¤H¶·½T«O¤uµ{¶µ¥Øªº³]p¡B«Ø³y¤ÎÀç¿ì¡A«ö·Ó¤Uz¸ê®Æ¤Î±¹¬I¿ì²z¡GÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ©Ò»¡©úªº¸ê®Æ¤Î¦U¶µ«Øij¡F¥Ó½Ð¤å¥ó¥]¬A©Ò¦³ªþ¥ó (¥Ó½Ð®Ñ½s¸¹¡GAEP-226/2005¡BVEP-221/2006¡BVEP-405/2013, VEP-408/2013¤Î VEP-494/2016)¡Fµn°O¥U¤ºªº¨ä¥L¬ÛÃö¤å¥ó¡F¥»³\¥iÃÒ©Ò»¡©úªº¸ê®Æ©Î½w¸Ñ±¹¬I¡F®Ú¾Ú¥»³\¥iÃÒ¤º¸üªº±ø¥ó¶·¦V¸pªø¦s©ñ©ÎÀò¸pªø§å㪺´£¥æ¤å¥ó©Ò«Øijªº½w¸Ñ±¹¬I¡F¥H¤Î¦b¤uµ{¶µ¥Ø¦U¶¥¬q¶i¦æªº«ùÄòºÊ¹î¤ÎºÊ´ú¤u§@©Ò«Øijªº½w¸Ñ±¹¬I¡Cµn°O¥U¤ºªº¤å¥ó©Òz«Øij¦p¨S¦³¦b¥»³\¥iÃÒ©ú½Tªí¥Ü¡A«h¤´¶·¹ê¬I³o¨Ç«Øij¡A°£«DÀò¥»³\¥iÃÒ©ú½TÁÅ°£©ÎÀq¥Ü×q¡C
1.8 All submissions, as required
under this Permit, shall be rectified and resubmitted in accordance with the
comments, if any made by the Director within one month of the receipt of the
Director¡¦s comments or otherwise as specified by the Director.
©Ò¦³«ö¥»³\¥iÃÒ³W©w´£¥æªº¤å¥ó¡A¶·¦b±µÀò¸pªøªº·N¨£ (¦p¦³ªÌ) «á1Ӥ뤺
(°£«D¸pªø¥t¦æ«ü©w)¡A®Ú¾Ú¸pªøªº·N¨£¥[¥H×¥¿¨Ã¦A¦V¸pªø´£¥æ¡C
1.9 All submissions approved by the
Director, all submissions deposited without comments by the Director, or all
submissions rectified in accordance with comments by the Director under this
Permit shall be construed as part of the permit conditions described in Part C of this Permit. Any variation of the submissions
shall be approved by the Director in writing or as prescribed in the relevant
permit conditions. Any non-compliance with the submissions may constitute a
contravention of the Environmental Impact Assessment Ordinance (Cap. 499). All submissions or any variation of the submissions shall be
certified by the Environmental Team (ET) Leader and verified by the Independent
Environmental Checker (IEC) referred to in Conditions 2.1 and 2.2 below, before
submitting to the Director under the Permit.
¸pªø§å㪺©Ò¦³´£¥æ¤å¥ó¡B¸pªø¨S¦³µ¹¤©·N¨£ªº©Ò¦³¦s©ñ¤å¥ó©Î®Ú¾Ú¥»³\¥iÃÒ³W©w¥Ñ¸pªøµ¹¤©·N¨£×¥¿ªº©Ò¦³´£¥æ¤å¥ó¡A§¡¶·¸àÄÀ¬°¥»³\¥iÃÒC³¡»¡©úªº³\¥iÃÒ±ø¥óªº¤@³¡¤À¡C´£¥æ¤å¥ó¦p¦³¥ô¦ó×q¡A§¡¶·Àò¸pªøªº®Ñ±§åã¡A©Î²Å¦X¦³Ãö³\¥iÃÒ±ø¥óq©úªº³W©w¡C¦p¦³¤£²Å¦X´£¥æ¤å¥óªº±¡ªp¡A¥i¯à¹H¤ÏÀôµû±ø¨Ò (²Ä499³¹) ªº³W©w¡C©Ò¦³´£¥æ¤å¥ó©Î´£¥æ¤å¥óªº¥ô¦ó×q¥»¡A§¡¶·«ö¤U¤å±ø¥ó²Ä2.1¤Î2.2¶µ©Òz¥ÑÀô¹Ò¤p²Õ²Õªø®ÖÃҤοW¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê¡AµM«á¤~«ö¥»³\¥iÃÒªº³W©w¦V¸pªø´£¥æ¡C
1.10 The Permit Holder shall release all
finalized submissions, as required under this Permit, to the public by
depositing copies in the EIAO Register Office, or in any other places, or any
internet websites as specified by the Director, or by any other means as
specified by the Director for public inspection. For this purpose, the Permit
Holder shall provide sufficient copies of the submissions.
³\¥iÃÒ«ù¦³¤H¶·§â©Ò¦³«ö¥»³\¥iÃÒ³W©w´£¥æªº¤å¥ó©w½Z¤½¶}µ¹¤½²³ª¾¹D¡A¤èªk¬O§â¦³Ãö¤å¥ó½Æ¥»¦s©ñ©óÀôµû±ø¨Òµn°O¥U¿ì¨Æ³B¡B¸pªø«ü©wªº¥ô¦ó¨ä¥L¦a¤è¡B¸pªø«ü©wªº¥ô¦ó¤¬Ápºôºô¯¸©Î±Ä¨ú¸pªø«ü©wªº¥ô¦ó¤èªk¡A¥H¨Ñ¤½²³¬d¾\¡C¦]¦¹¡A³\¥iÃÒ«ù¦³¤H¶·´£¨Ñ¨¬°÷¼Æ¶qªº½Æ¥»¡C
1.11 All submissions to the Director required
under this Permit shall be delivered either in person or by registered mail to
the EIAO Register Office (currently at 27/F, Southorn Centre,
¥»³\¥iÃÒ³W©w¦V¸pªø´£¥æªº©Ò¦³¤å¥ó¡A¶·¿Ë¨°e¥æ©Î¥H±¾¸¹¤è¦¡¶l±H¦ÜÀôµû±ø¨Òµn°O¥U¿ì¨Æ³B (²{§}¬°¡G»´äÆW¥J°a¥§¸Ö¹D130¸¹×¹y¤¤¤ß27¼Ó)¡C©Ò¦³«ö¥»³\¥iÃÒ³W©w´£¥æªº¤å¥ó©w½Zªº¹q¤lª©¥»¡A§¡¶·¥H¶W¤å¥»¼Ð¥Ü»y¨¥ (HTML) (²Ä4.0©Î¸û«áª©¥») ¤Î«KÄ⦡¤å¥ó®æ¦¡ (PDF) (²Ä4.0©Î¸û«áª©¥») »s§@¡A°£«D¥tÀò¸pªø¦P·N¡A¨Ã¶·»Pµw½Æ¥»¦P®É´£¥æ¡C
1.12 The Permit Holder shall notify the Director
in writing the commencement date of construction of the Project prior to the
commencement of construction of the Project. The Permit Holder shall notify the
Director in writing immediately if there is any change of the commencement date
of the construction.
³\¥iÃÒ«ù¦³¤H¶·¦b¤uµ{¶µ¥Øªº«Ø³y¤uµ{®i¶}«e¡A¥H®Ñ±¤è¦¡§â«Ø³y¤uµ{ªº¬I¤u¤é´Á³qª¾¸pªø¡C¬I¤u¤é´Á¦p¦³¥ô¦ó§ó§ï¡A³\¥iÃÒ«ù¦³¤H¥²¶·¥ß§Y¥H®Ñ±¤è¦¡³qª¾¸pªø¡C
1.13 For the purpose of this Permit, ¡§commencement of
construction¡¨ does not include works related to site clearance and preparation,
or other works as agreed by the Director.
¬°°õ¦æ¥»³\¥iÃÒ¡A¡u«Ø³y¤uµ{ªº®i¶}¡v¤£¥]¬A¦³Ãö¤u¦a²M²z¤Î¹w³Æªº¤uµ{¡A©Î¸pªø¦P·Nªº¨ä¥L¤uµ{¡C
2. Submissions
or Measures before Commencement of Construction of the Project
¤uµ{¶µ¥Øªº«Ø³y¤uµ{®i¶}«e¶·´£¥æªº¤å¥ó©Î±Ä¨úªº±¹¬I
Employment of Environmental Monitoring and Audit (EM&A)
Personnel
¸u¥ÎÀô¹ÒºÊ¹î¤Î¼f®Ö (¡uÀôºÊ¡v)¤Hû
2.1 An Environmental Team (ET) shall be established by the Permit Holder no
later than one month before the commencement of construction of the Project.
The ET shall not be in any way an associated body of the Contractor or the Independent
Environmental Checker (IEC) for the Project. The ET shall be headed by an ET
Leader. The ET Leader shall be a person who has at least 7 years of experience
in environmental monitoring and auditing (EM&A) or environmental
management. The ET and the ET Leader shall be responsible for the
implementation of the EM&A programme in accordance with the EM&A
requirements as contained in the EM&A Manual of the Project. The ET Leader
shall keep a contemporaneous log-book of each and every instance or circumstance
or change of circumstances, which may affect the compliance with the
recommendations of the EIA Report (Register No.: AEIAR-086/2005) and this
Permit. The ET Leader shall notify the IEC within one working day of the
occurrence of any such instance or circumstance or change of circumstances. The
ET Leader¡¦s log-book shall be kept readily available for inspection by all
persons assisting in supervision of the implementation of the recommendations
of the EIA Report (Register No.: AEIAR-086/2005) and this Permit or by the
Director or his authorized officers. Failure to maintain records in the
log-book, failure to discharge the duties of the ET Leader as defined in the
EM&A Manual or failure to comply with this Condition would entitle the
Director to require the Permit Holder by notice in writing to replace the ET
Leader. Failure by the Permit Holder to make replacement, or further failure to
keep contemporaneous records in the log-book despite the employment of a new ET Leader may
render the Permit liable to suspension, cancellation or variation.
¦b¤uµ{¶µ¥Øªº«Ø³y¤uµ{®i¶}«e¡A³\¥iÃÒ«ù¦³¤H¶·¦Ü¤Ö´£¦1Ӥ릨¥ß¤@ÓÀô¹Ò¤p²Õ¡CÀô¹Ò¤p²Õ¤£±o»P¤uµ{¶µ¥Øªº©Ó¿ì°Ó©Î¿W¥ßÀô¹Ò¬d®Ö¤H¦³¥ô¦óÁpô¡CÀô¹Ò¤p²Õ¶·¥Ñ¤@¦WÀô¹Ò¤p²Õ²Õªø±a»â¡CÀô¹Ò¤p²Õ²Õªø¶·¦bÀô¹ÒºÊ¹î¤Î¼f®Ö (¡uÀôºÊ¡v)©ÎÀô¹ÒºÞ²z¤è±¦Ü¤Ö¦³7¦~¸gÅç¡CÀô¹Ò¤p²Õ¤ÎÀô¹Ò¤p²Õ²Õªø¶·«ö¤uµ{¶µ¥ØªºÀôºÊ¤â¥U¤º¸üªºÀôºÊ³W©w¡A°õ¦æÀôºÊp¹º¡CÀô¹Ò¤p²Õ²Õªø¶·«O¦s¤@¥»°O¿ý¥U¡A¦P®É°O¸ü¥i¯à·|¼vÅTÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ªº«Øij¤Î¥»³\¥iÃÒªº²Å¦X±¡ªpªº¨C©v¨Æ¥ó¡B¨CºØ±¡ªp©Î¨C¦¸±¡ªpÅܤơCÀô¹Ò¤p²Õ²Õªø¶·¦bµo¥Í¥ô¦óÃþ¦ü¨Æ¥ó¡B±¡ªp©Î±¡ªpÅܤƫá1Ó¤u§@¤Ñ¤º³qª¾¿W¥ßÀô¹Ò¬d®Ö¤H¡C¦s©ñÀô¹Ò¤p²Õ²Õªøªº°O¿ý¥Uªº¦a¤è¡A¶·¥i¨Ñ¨ó§U·þ¾É°õ¦æÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ªº«Øij¤Î¥»³\¥iÃÒªº©Ò¦³¤H¤h¡B¸pªø©ÎÀò±ÂÅv¤HûÀH®É¬d¾\¡CÀô¹Ò¤p²Õ²Õªø¦p¥¼¯à¦b°O¿ý¥U«O¦s°O¿ý¡B¥¼¯à°õ¦æÀôºÊ¤â¥U©Ò¦C©úªºÀô¹Ò¤p²Õ²Õªø¾°È©Î¥¼¯à²Å¦X¥»±ø¥óªº³W©w¡A¸pªø¦³Åv¥H®Ñ±n¨D³\¥iÃÒ«ù¦³¤HºM´«Àô¹Ò¤p²Õ²Õªø¡C³\¥iÃÒ«ù¦³¤H¦p¥¼¯à¦w±Æ¤H¿ï´À¸É¡A©Î¦b¸u¥Î·sÀô¹Ò¤p²Õ²Õªø«á¤´¥¼¯à¦b°O¿ý¥U«O¦s¦P´Áªº°O¿ý¡A©Î·|¾ÉP³\¥iÃÒ¾D¼È®É¦Q¾P¡B¨ú®ø©Î§ó§ï¡C
2.2 An IEC shall be employed by the
Permit Holder no later than one month before commencement of construction of
the Project. The IEC shall not be in any way an associated body of the
Contractor or the ET for the Project. The IEC shall be a person who has at
least 7 years of experience in EM&A or environmental management. The IEC
shall be responsible for duties defined in the EM&A Manual and shall audit
the overall EM&A performance, including the implementation of all environmental
mitigation measures, submissions required in the EM&A Manual, and any other
submissions required under this Permit. In addition, the IEC shall be
responsible for verifying the environmental acceptability of permanent and
temporary works, relevant design plans and submissions under this Permit. The
IEC shall verify the log-book(s) mentioned in Condition 2.1 of this Permit. The
IEC shall notify the Director by fax, within one working day of receipt of
notification from the ET Leader of each and every occurrence, change of
circumstances or non-compliance with the EIA Report (Register No.:
AEIAR-086/2005) and this Permit, which might affect the monitoring or control
of adverse environmental impacts from the Project. In the case where the IEC
fails to so notify the Director of the same, fails to discharge the duties of
the IEC as defined in the EM&A Manual or fails to comply with this
Condition, the Director may require the Permit Holder by notice in writing to
replace the IEC. Failure to replace the IEC as directed or further failure to
so notify the Director despite employment of a new IEC may render the Permit
liable to suspension, cancellation or variation. Notification by the Permit
Holder is the same as notification by the IEC for the purpose of this Condition.
¦b¤uµ{¶µ¥Øªº«Ø³y¤uµ{®i¶}«e¡A³\¥iÃÒ«ù¦³¤H¶·¦Ü¤Ö´£¦1Ó¤ë¸u¥Î¤@¦W¿W¥ßÀô¹Ò¬d®Ö¤H¡C¿W¥ßÀô¹Ò¬d®Ö¤H¤£±o»P¤uµ{¶µ¥Øªº©Ó¿ì°Ó©ÎÀô¹Ò¤p²Õ¦³¥ô¦óÁpô¡C¿W¥ßÀô¹Ò¬d®Ö¤H¶·¦bÀôºÊ©ÎÀô¹ÒºÞ²z¤è±¦Ü¤Ö¦³7¦~¸gÅç¡C¿W¥ßÀô¹Ò¬d®Ö¤H¶·°õ¦æÀôºÊ¤â¥U©Ò¦C©úªºÂ¾°È¡A¥H¤Î¼f®Ö¾ãÅéÀôºÊ¤u§@ªºªí²{¡A¥]¬A¹ê¬I©Ò¦³Àô¹Ò½w¸Ñ±¹¬I¡B´£¥æÀôºÊ¤â¥U³W©wªº¤å¥ó¡A¥H¤Î´£¥æ¥»³\¥iÃÒ©Òn¨Dªº¨ä¥L¤å¥ó¡C¦¹¥~¡A¿W¥ßÀô¹Ò¬d®Ö¤H¶·®Ö¹ê¥Ã¤[¤ÎÁ{®É¤uµ{¦bÀô¹Ò¤Wªº¥i±µ¨üµ{«×¡B¬ÛÃöªº³]p¹Ï«h©M®Ú¾Ú¥»³\¥iÃÒ´£¥æªº¤å¥ó¡A¨Ã¶·®Ö¹ê¥»³\¥iÃÒ±ø¥ó²Ä2.1¶µ©Òzªº°O¿ý¥U¡C¦b¨C¦¸¥X²{¨Æ¬G¡B±¡ªpÅܤƩΤ£²Å¦XÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ¤Î¥»³\¥iÃÒªº±¡ªp¡A¦Ó¥i¯à·|§«Ãª¤uµ{¶µ¥Ø©Ò³y¦¨¤£¨}Àô¹Ò¼vÅTªººÊ¹î©Î±±¨î¤u§@®É¡A¿W¥ßÀô¹Ò¬d®Ö¤H¶·¦b±µÀòÀô¹Ò¤p²Õ²Õªø³qª¾«á1Ó¤u§@¤Ñ¤º¥H¶Ç¯u¤è¦¡³qª¾¸pªø¡C¿W¥ßÀô¹Ò¬d®Ö¤H¦p¥¼¯à³qª¾¸pªø¦³Ãö±¡ªp¡B¥¼¯à°õ¦æÀôºÊ¤â¥U©Ò¦C©úªº¿W¥ßÀô¹Ò¬d®Ö¤H¾°È©Î¥¼¯à²Å¦X¥»±ø¥óªº³W©w¡A¸pªø¥i¥H®Ñ±n¨D³\¥iÃÒ«ù¦³¤HºM´«¿W¥ßÀô¹Ò¬d®Ö¤H¡C¦p¥¼¯à«ö«ü¥ÜºM´«¿W¥ßÀô¹Ò¬d®Ö¤H¡A©Î¦b¸u¥Î·s¿W¥ßÀô¹Ò¬d®Ö¤H«á¤´¥¼¯à³qª¾¸pªø¦³Ãö±¡ªp¡A«h©Î·|¾ÉP³\¥iÃÒ¾D¼È®É¦Q¾P¡B¨ú®ø©Î§ó§ï¡C¬°°õ¦æ¥»±ø¥ó¡A³\¥iÃÒ«ù¦³¤Hªº³qª¾µ¥¦P¿W¥ßÀô¹Ò¬d®Ö¤Hªº³qª¾¡C
¥Dn«Ø³y¤½¥qªººÞ²z¬[ºc
2.3 The Permit Holder shall,
at least one week before the commencement of construction of the Project, inform the Director in writing the
management organization of the main construction companies and/or any form of
joint ventures appointed for the Project. The information, to be
submitted, shall include at least an organization chart, names of responsible
persons and their contact details.
³\¥iÃÒ«ù¦³¤H¶·¦b¤uµ{¶µ¥Øªº«Ø³y¤uµ{®i¶}«e¡A¦Ü¤Ö´£¦1Ó¬P´Á§â¬°¤uµ{¶µ¥Ø¸u¥Îªº¥Dn«Ø³y¤½¥q¤Î / ©Î¥ô¦ó§Î¦¡ªº¦XÀç¥ø·~ªººÞ²z¬[ºc¡A¥H®Ñ±³qª¾¸pªø¡C´£¥æªº¸ê®Æ¶·¦Ü¤Ö¥]¬A¤@¥÷²Õ´¹Ï¡Bt³d¤Hªº©m¦W¤ÎÁpµ¸¸ê®Æ¡C
3. Measures
during Construction of the Project
¤uµ{¶µ¥Ø«Ø³y´Á¶¡¶·±Ä¨úªº±¹¬I
Measures
to Mitigate Water Quality Impact
¤ô½è¼vÅT½w¸Ñ±¹¬I
3.1 To
minimize the site runoff, catchpits and perimeter channels shall be constructed
in advance of site formation works and earthworks.
¬°´î¤Ö¤u¦a®|¬y¡A¦b¶i¦æ¤u¦a¥¾ã¤uµ{¤Î¤g¤ì¤u¨Æ¤§«e¡A¶·¥ý¦æ«Ø³yºI¤ô¤«¤Î©PÃä¤ô¹D¡C
3.2 To
minimize the site runoff, open stockpiles of construction materials on site
shall be covered with tarpaulin or similar fabric during rainstorms.
¬°´î¤Ö¤u¦a®|¬y¡A¦b¼É«B´Á¶¡¡A¤u¦a¤ºÅS¤Ñ°ï¦sªº«Ø¿v§÷®Æ¶·¥Î¦|¥¬©Î¦PÃþª«®ÆÂл\¡C
3.3 To
mitigate the water quality impact, portable chemical toilets shall be provided
during construction of the Project.
¬°½w¸Ñ¹ï¤ô½è³y¦¨ªº¼vÅT¡A¦b¤uµ{¶µ¥Øªº«Ø³y¤uµ{´Á¶¡¡A¶·´£¨Ñ¨Ï¥Î¤Æ¾Ç¾¯²M²zªº¬y°Ê´Z©Ò¡C
3.4 To
mitigate the water quality impact, discharges of surface runoff into foul
sewers shall not be allowed.
¬°½w¸Ñ¹ï¤ô½è³y¦¨ªº¼vÅT¡A¤£±o§â¦a±®|¬y±Æ¤J¦Ã¤ô´ë¡C
3.5 To
mitigate the water quality impact, temporary access roads shall be surfaced
with hard core such as crushed stone or gravel.
¬°½w¸Ñ¹ï¤ô½è³y¦¨ªº¼vÅT¡AÁ{®É³q¸ô¶·¥Hµw¶ñ®Æ¦p¸H¥Û©Î¬âÄt¾Q±¡C
Measures to Manage Construction and Demolition Waste Impact
©î«Ø¼o®Æ¼vÅTºÞ²z±¹¬I
3.6 To manage the construction and demolition
(C&D) waste impact, C&D materials arising from the Project shall be
reused in the Project site. No such
surplus C&D materials shall be disposed of anywhere except the public
filling facilities and the
¬°ºÞ²z©î«Ø¼o®Æ³y¦¨ªº¼vÅT¡A¦]¤uµ{¶µ¥Ø²£¥Íªº©î«Øª«®Æ¶·¦b¤uµ{¶µ¥Øªº¤u¦a¤W´`Àô¦A¥Î¡C°£¤½²³¶ñ¤g³]¬I¤Î·s¬É¦è°ï¶ñ°Ï©Î¸pªø¦P·Nªº¨ä¥L¦aÂI¥~¡A³Ñ¾lªº©î«Øª«®Æ¤£±o¦b¥ô¦ó¨ä¥L¦a¤è±ó¸m¡C
Measures to Mitigate Landfill Gas Hazard
°ï¶ñ°Ï®ðÅé·ÀI½w¸Ñ±¹¬I
3.7 To
mitigate the landfill gas hazard, all buildings and enclosed structures,
including temporary offices, temporary stores and the Administration Building,
within the
(i) building
shall
be raised clear of the ground with a clear separation distance (as measured from the highest point on
the ground surface to the underside of the lowest floor joist) of at least
(ii) a
low-gas permeability
membrane shall be applied to the surface of any wall or floor slab that rest on
or is below ground. A gravel-fill vent system shall be provided such that
passive venting is achieved around the perimeter of the structure. In addition,
other building materials, such as dense well-compacted concrete or steel
shuttering which provide a measure of resistance to gas permeation, shall be
used to achieve gas protection.
¬°½w¸Ñ°ï¶ñ°Ï®ðÅé·ÀI¡A¦b¤p§N¤ô°ï¶ñ°Ï
(i) «Ø¿vª«¶·¥[°ª¦Ü¶ZÂ÷¦a±¦Ü¤Ö500²@¦Ì (¥Ñ¦a±³Ì°ªÂIp¦Ü³Ì§C¦aªO¦«¼Ùªº©³±)¡F©Î
(ii) ¦b¥ô¦óÀð¾À©Î¦a±¤W©Î¤Uªº¦a¥x¾Q¤W§C®ðÅ麯³z«×Á¡½¤¡C¶·´£¨Ñ¤@Ó¥H¬âÄt¥R¶ñªº³q·¨t²Î¡AÅý³Q°Ê¦¡±Æ®ð¥i©óºc¿vª«ªº¥~³ò§¹¦¨¡C¦¹¥~¡A¶·±Ä¥Î¥i´£¨Ñ§Ü®ðÅ麯º|±¹¬Iªº¨ä¥L«Ø¿vª«®Æ¡A¦pºò±K§¹¾ãÀ£¹ê²V¾®¤g©Î¿û³òªO¡A¥H¹FP®ðÅ騾Å@ªº®ÄªG¡C
Measures
to Mitigate Landscape and Visual Impacts
´ºÆ[¬ü¤Æ¤Îµøı¼vÅT½w¸Ñ±¹¬I
3.8 To mitigate the landscape and
visual impacts arising from the Project, landscape and visual mitigation
measures shall be implemented in accordance with Figure 3 attached to this Permit.
¬°½w¸Ñ¤uµ{¶µ¥Ø¤ÞPªº´ºÆ[¬ü¤Æ¤Îµøı¼vÅT¡A¶·«ö·Ó¥»³\¥iÃÒ¹Ï3°õ¦æ´ºÆ[¬ü¤Æ¤Îµøı¼vÅT½w¸Ñ±¹¬I¡C
4. Measures
during Operation of the Project
¤uµ{¶µ¥ØÀç¿ì´Á¶¡¶·±Ä¨úªº±¹¬I
Measures
to Mitigate Environmental Impacts
Àô¹Ò¼vÅT½w¸Ñ±¹¬I
4.1 To
review the environmental impacts, a Process Review/Design Audit shall be
carried out as described in Condition 5.2.
¬°ÀË°Q¹ïÀô¹Ò³y¦¨ªº¼vÅT¡A¶·«ö·Ó±ø¥ó²Ä5.2¶µ©Ò»¡©ú¡A¶i¦æ¤u§ÇÀË°Q / ³]p¼f®Ö¡C
Measures
to Mitigate Air Quality Impact
ªÅ®ð½è¯À¼vÅT½w¸Ñ±¹¬I
4.2 To mitigate the air quality
impact, chimney(s) shall be designed and operated in accordance with the
parameters, including stack height, stack diameter, efflux velocity, exit
temperature and maximum permissible pollutant emission rate, as described in Annex A attached to this Permit.
¬°½w¸Ñ¹ïªÅ®ð½è¯À³y¦¨ªº¼vÅT¡A¶·«ö·Ó¥»³\¥iÃÒªþ¥óA©Ò»¡©úªº°Ñ¼Æ¡A¥]¬A·Ï§w°ª«×¡B·Ï§wª½®|¡B¼o®ð±Æ¥Xªº³t«×¡B¼o®ð±Æ¥X®Éªº·Å«×¤Î³Ì°ª³\¥i¦Ã¬Vª«±Æ©ñ²v¡A³]p¨ÃÀç¿ì·Ï§w¡C
4.3 To
minimize the air quality impact, no chimney shall be installed within the
¡§chimney restricted area¡¨ as shown in Figure
4 attached to this Permit.
¬°´î¤Ö¹ïªÅ®ð½è¯À³y¦¨ªº¼vÅT¡A¤£±o¦b¥»³\¥iÃÒ¹Ï4©Ò¥Ü¡u·Ï§wºÞ¨î°Ï¡v¤º¸Ë³]·Ï§w¡C
4.4 Unless otherwise approved by the Director upon the submission of a
detailed proposal, no chimney
emissions associated with the operation of the Project shall be allowed between
19:00 and 07:00 hours daily.
°£«D©Ò´£¥æªº¸Ô²Óij®×¥tÀò¸pªø§åã¡A¨C±ß¤C®É¦Ü²Ý±á¤C®É¤§¶¡¡A·Ï§w¤£±o±Æ©ñ»PÀç¿ì¤uµ{¶µ¥Ø¬ÛÃöªº¼o®ð¡C
4.5 To
minimize the air quality impact, the following recycling processes as
screened-out in the EIA Report (Register No.:
AEIAR-086/2005) shall not be allowed for the Project:
(i)
inedible rendering of organic food waste;
(ii)
melting of ferrous metal;
(iii)
demagging process (reduction of magnesium) from secondary
aluminum recovery; and
(iv)
chlorine bleaching process for paper and wood.
¬°´î¤Ö¹ïªÅ®ð½è¯À³y¦¨ªº¼vÅT¡A¤£±o¬°¤uµ{¶µ¥Ø¶i¦æÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ¿z¥hªº¤Uz´`Àô¦A³y¤u§Ç¡G
(i) ¦³¾÷¹ª«´í·ºªº«D¹¥Î´£·Ò¤u§Ç¡F
(ii) §tÅKª÷Äݪºº²¤Æ¤u§Ç¡F
(iii) ¦^¦¬¦A¥Í¾Tªº°£Áâ (®ø´îÁâ) ¹Lµ{¡F¥H¤Î
(iv) ¯È±i¤Î¤ì§÷ªº´âº}¥Õµ{§Ç¡C
4.6 To
mitigate the air quality impact, locations of fresh air intakes within the
Project site shall be restricted to or below 22.5mPD.
¬°½w¸Ñ¹ïªÅ®ð½è¯À³y¦¨ªº¼vÅT¡A¤uµ{¶µ¥Øªº¤u¦a¤ºÂA·¤J¤fªº¦ì¸m¶·©ó¥D¤ô¥°ò·Ç¥H¤W
4.7 To
minimize the emission of sulphur dioxide from fuel combustion, only ultra-low
sulphur diesel (diesel with 0.005% sulphur content by weight) or other cleaner
fuel(s) as agreed by the Director shall be used for all activities requiring
liquid fuel during operation of the Project.
¬°´î¤Ö¿U®Æ¿U¿N¹Lµ{©Ò±Æ©ñªº¤G®ñ¤Æ²¸¡A¦bÀç¿ì¤uµ{¶µ¥Ø´Á¶¡¡A¥u¥i¨Ï¥Î¶W§C§t²¸¶q®ãªo («ö«¶qp§t0.005%²¸ªº®ãªo) ©Î¸pªø¦P·Nªº¨ä¥L¸û§C¦Ã¬V¿U®Æ¡A¶i¦æ»Ýn²GÅé¿U®Æªº¦U¶µ¬¡°Ê¡C
Measures
to Mitigate Hazard to life Impact
¥Í©R¦M®`½w¸Ñ±¹¬I
4.8 To
minimize the hazard to life impact, no chlorine shall be stored or transported
within the Project site during operation of the Project.
¬°´î¤Ö¹ï¥Í©R³y¦¨¦M®`¡A¦bÀç¿ì¤uµ{¶µ¥Ø´Á¶¡¡A¤£±o¦b¤uµ{¶µ¥Øªº¤u¦a¤º¶J¦s©Î¹B°e´â¡C
4.9 To
mitigate the hazard to life impact, dangerous goods supporting combustion
including oxygen, acetylene, hydrogen peroxide, rubber tyres and diesel shall
not be stored or located within
¬°½w¸Ñ¹ï¥Í©R³y¦¨¦M®`¡A¦b¤uµ{¶µ¥Øªº¤u¦a¬É½u°_p
4.10 To
mitigate the hazard to life impact, heights of buildings along the western
boundary of the Project site shall be limited, if any person works at the
elevated levels of the buildings, as indicated in Annex B
attached to this Permit.
¬°½w¸Ñ¹ï¥Í©R³y¦¨¦M®`¡A¦p¥ô¦ó¤H¤h¦bªu¤uµ{¶µ¥Ø¤u¦a¦è±¬É½uªº«Ø¿vª«°ª¼h¤u§@¡A«Ø¿vª«ªº°ª«×¶·«ö·Ó¥»³\¥iÃÒªþ¥óB©Ò¥Ü¨ü¨ì¨î¡C
Measures to Prevent Land
Contamination
¤g¦a¦Ã¬V¹w¨¾±¹¬I
4.11 To prevent the land contamination, any areas
within the Project site for recycling activities and chemical storage shall be
paved with concrete.
¬°¹w¨¾¤g¦a¨ü¨ì¦Ã¬V¡A¤uµ{¶µ¥Øªº¤u¦a¤º¥ô¦ó¶i¦æ´`Àô¦A³y¬¡°Ê¤Î¶J¦s¤Æ¾Ç«~ªº¦a¤è¡A§¡¶·¾Q¥H²V¾®¤g¡C
4.12 To prevent the land
contamination, all fuel tanks and chemical storage areas shall be sited on
sealed areas within bunds of a capacity at least equal to 110% of the storage
capacity of the largest tank.
¬°¹w¨¾¤g¦a¨ü¨ì¦Ã¬V¡A©Ò¦³¿U®Æ¬û¤Î¤Æ¾Ç«~¶J¦s°Ï¶·³]©ó«Ê³¬°Ïªº³öéP¤º¡A³öéPªº©Ó¸ü¯à¤O¶·¦Ü¤Ö¬Ûµ¥©ó³Ì¤j¿U®Æ¬û¶J¦s¶qªº110%¡C
Measures to Mitigate Landfill Gas Hazard
°ï¶ñ°Ï®ðÅé·ÀI½w¸Ñ±¹¬I
4.13 To mitigate the landfill gas hazard,
landfill gas hazard mitigation measure as described in Condition 3.7 shall be
implemented during operation of the Project.
¬°½w¸Ñ°ï¶ñ°Ï®ðÅé·ÀI¡A¦bÀç¿ì¤uµ{¶µ¥Ø´Á¶¡¡A¶·°õ¦æ±ø¥ó²Ä3.7¶µ©Ò»¡©úªº½w¸Ñ±¹¬I¡C
Maintenance of Landscape and Visual Measures
«ùÄò°õ¦æ´ºÆ[¬ü¤Æ¤Îµøı¼vÅT½w¸Ñ±¹¬I
4.14 To
mitigate the landscape and visual impacts, all landscape and visual mitigation
measures as described in Condition 3.8 shall be properly maintained during
operation of the Project.
¬°½w¸Ñ´ºÆ[¬ü¤Æ¤Îµøı¼vÅT¡A¦bÀç¿ì¤uµ{¶µ¥Ø´Á¶¡¡A¶·§´µ½¨Ã«ùÄò°õ¦æ±ø¥ó²Ä3.8¶µ©Ò»¡©úªº©Ò¦³´ºÆ[¬ü¤Æ¤Îµøı¼vÅT½w¸Ñ±¹¬I¡C
Measures for the Plant Collecting Spent
¦¬¶°¼o¹q¦À¥H¦^¦¬¹]ªº¼t©Ð¶·±Ä¨úªº±¹¬I
4.15 To mitigate the environmental
impacts from a spent battery recycling plant located at Lot EP11-01(2) as shown
in Figure 5, the plant design,
mitigation measures and operational measures in Annex C
shall be implemented. The processing capacity of the plant per annum (measured
in a 12-consecutive-month period) should not be more than 41,600 tonnes of spent
battery being collected or 33,300 tonnes of lead being extracted, whichever is
lower.
¬°½w¸Ñ¹Ï5©Ò¥Ü¦ì©óEP11-01(2)¦a¬qªº¼o¹q¦À¦^¦¬¼t¹ïÀô¹Òªº¼vÅT¡A¶·°õ¦æªþ¥óC©Ò¦Cªº¼t©Ð³]p¡A½w¸Ñ±¹¬I¤ÎÀç¿ì±¹¬I¡C¦b¸Ó¼t©Ðªº¥[¤u®e¶q(©ó³sÄò12Ӥ몺´Á¶¡¤º¶i¦æ¶q«×)¤è±¡A¨C¦~¤£À³¦¬¶°¦h©ó41, 600¤½¾·ªº¼o¹q¦À©Î©â¨ú¦h©ó33, 300¤½¾·ªº¹](¥H¸û§CªÌ¬°·Ç)¡C
Measures for the Plant Collecting Waste Electrical and Electronic
Equipment (WEEE) at Lot P2, P3 and P4
©ó¦a¬qP2, P3 ¤ÎP4¦¬¶°¼o¹q¾¹¹q¤l²£«~ªº¼t©Ð¶·±Ä¨úªº±¹¬I
4.16 To mitigate the environmental impacts from the Waste Electrical and Electronic Equipment plant at Lots P2, P3 and P4 as shown in Figure 6, the plant design, mitigation measures and operational measures in Annex D shall also be implemented. The processing capacity of the plant per annum (measured in a 12-consecutive month period) should not be more than 56,000 tonnes of Waste Electrical and Electronic Equipment.
¬°½w¸Ñ¹Ï6©Ò¥Ü¦ì©ó¦a¬qP2,
P3¤ÎP4ªº¼o¹q¾¹¹q¤l²£«~ªº¼t©Ð¹ïÀô¹Òªº¼vÅT¡A¶·°õ¦æªþ¥óD©Ò¦Cªº¼t©Ð³]p¡A½w¸Ñ±¹¬I¤ÎÀç¿ì±¹¬I¡C¦b¸Ó¼t©Ðªº³B²z®e¶q(©ó³sÄò12Ӥ몺´Á¶¡¤º¶i¦æ¶q«×)¤è±¡A¨C¦~¤£À³¦h©ó56, 000¤½¾·ªº¼o¹q¾¹¹q¤l²£«~¡C
Measures for the Plant Collecting Waste Paper
¦¬¶°¼o¯Èªº¼t©Ð¶·±Ä¨úªº±¹¬I
4.17 To mitigate the environmental impacts
from a plant collecting waste paper, the plant design, mitigation measures and
operational measures in Annex F shall be implemented. The processing
capacity of the plant per annum (measured in a 12-consecutive-month period)
should not be more than 1,000,000 tonnes of waste paper.
¬°½w¸Ñ¼o¯È¦^¦¬¼t¹ïÀô¹Òªº¼vÅT¡A¶·°õ¦æªþ¥óF©Ò¦Cªº¼t©Ð³]p¡A½w¸Ñ±¹¬I¤ÎÀç¿ì±¹¬I¡C¦b¸Ó¼t©Ðªº¥[¤u®e¶q(©ó³sÄò12Ӥ몺´Á¶¡¤º¶i¦æ¶q«×)¤è±¡A¨C¦~¤£À³¦¬¶°¦h©ó1,000,000¤½¾·ªº¼o¯È¡C
5. Environmental
Monitoring and Audit Requirements
Àô¹ÒºÊ¹î¤Î¼f®Ö³W©w
5.1 The
EM&A programme shall be implemented in accordance with the procedures and
requirements as set out in the EM&A Manual. Any changes to the programme
shall be justified by the ET Leader and verified by the IEC as conforming to
the information and requirements contained in the EM&A Manual before
submission to the Director for approval.
ÀôºÊp¹º¶·«ö·ÓÀôºÊ¤â¥U©Ò¸üµ{§Ç¤Î³W©w°õ¦æ¡Cp¹º¦p¦³§ó§ï¡A¶·¥ÑÀô¹Ò¤p²Õ²Õªø´£¥X¥R¤À²z¥Ñ¡A¨Ã¥Ñ¿W¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê¡AÃÒ©ú¨ä²Å¦XÀôºÊ¤â¥U¤º¸üªº¸ê®Æ¤Î³W©w¡AµM«á¤~´£¥æ¸pªø§åã¡C
5.2 To
ensure the findings and recommendations of the EIA Report (Register No.: AEIAR-086/2005) and the Permit are complied with, Process
Review shall be carried out in accordance with the EM&A Manual for all
recycling activities/facilities of the Project. If the result of the Process Review
indicates that the recycling activities/facilities are not covered by the EIA
Report (Register No.: AEIAR-086/2005) or deviates from
the development parameters listed in the EIA Report (Register
No.: AEIAR-086/2005) including the parameters in Annex A
attached to this Permit, Design Audit shall be carried out in accordance with
the EM&A Manual with a view to assessing the potential impacts and
recommending additional mitigation measures, if any, for various environmental
impacts including but not limited to air quality, hazard to life, waste
management and land contamination.
Otherwise, the parameters or scope of recycling activities/facilities
shall be modified in such a way that the findings of the EIA Report (Register
No.: AEIAR-086/2005) are complied with.
The Process Review/Design Audit shall be documented in accordance with
the EM&A Manual and shall be certified by the ET Leader and verified by the
IEC as conforming to the information and recommendations contained in the EIA
Report (Register No.: AEIAR-086/2005).
¬°½T«O²Å¦XÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ªºµ²ªG»P«Øij¤Î³\¥iÃÒªº±ø¥ó¡A¶·«ö·ÓÀôºÊ¤â¥U¬°¤uµ{¶µ¥Øªº©Ò¦³´`Àô¦A³y¬¡°Ê / ³]¬I¶i¦æ¤u§ÇÀË°Q¡C¦p¤u§ÇÀË°Qªºµ²ªGÅã¥Ü¡A¦³Ãö´`Àô¦A³y¬¡°Ê / ³]¬I¨Ã«DÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ©Ò²[»\ªº¡A©Î»PÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ©Ò¦Cªºµo®i°Ñ¼Æ (¥]¬A¥»³\¥iÃÒªþ¥óA©Ò¦C°Ñ¼Æ) ¤£¦P¡A«K¶·«ö·ÓÀôºÊ¤â¥U¶i¦æ³]p¼f®Ö¡A±q¦Óµû¦ô¥i¯à³y¦¨ªº¼vÅT¡A¨Ã´N¦UºØÀô¹Ò¼vÅT«Øij¨ä¥L½w¸Ñ±¹¬I (¦p¦³ªÌ)¡A³o¨Ç¼vÅT¥]¬A¦ý¤£©óªÅ®ð½è¯À¡B¥Í©R¦M®`¡B¼oª«ºÞ²z¤Î¤g¦a¦Ã¬V¡C§_«h¡A«K¶·×q´`Àô¦A³y¬¡°Ê / ³]¬Iªº°Ñ¼Æ©Î½d³ò¡A¥H²Å¦XÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ªºµ²ªG¡C¤u§ÇÀË°Q / ³]p¼f®Ö¶·«ö·ÓÀôºÊ¤â¥U¥H¤å¦r°O¿ý¡A¨Ã¶·¥ÑÀô¹Ò¤p²Õ²Õªø®ÖÃҤοW¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê¡AÃÒ©ú¨ä²Å¦XÀôµû³ø§i (µn°O¥U½s¸¹¡GAEIAR-086/2005) ¤º¸üªº¸ê®Æ¤Î«Øij¡C
5.3 One hard copy and one electronic copy of monthly EM&A Report during construction of
the project and quarterly EM&A Report during operation of the Project shall
be submitted to the Director in accordance with the EM&A Manual. The submissions shall be certified by
the ET Leader and verified by the IEC. Additional copies of the submission
shall be provided to the Director upon request by the Director.
«ö·ÓÀôºÊ¤â¥Uªº³W©w¡A¦b¤uµ{¶µ¥Ø«Ø³y´Á¶¡¡A¶·¦V¸pªø´£¥æ¨C¤ëÀôºÊ³ø§iªº1¥÷µw½Æ¥»¤Î1¥÷¹q¤lª©¥»¡F¦b¤uµ{¶µ¥ØÀç¿ì´Á¶¡¡A¶·¦V¸pªø´£¥æ¨C©uÀôºÊ³ø§iªº3¥÷µw½Æ¥»¤Î1¥÷¹q¤lª©¥»¡C´£¥æªº³ø§i¶·¥ÑÀô¹Ò¤p²Õ²Õªø®ÖÃҤοW¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê¡C¦p¸pªøn¨D¡A«h¶·´£¥æÃB¥~½Æ¥»¡C
5.4 Any changes to the monitoring and audit requirements shall be justified
by the ET Leader and verified by the IEC as conforming to the requirements set
out in the EM&A Manual, and shall be submitted to the Director for
approval.
ÀôºÊ³W©w¦p¦³§ó§ï¡A¶·¥ÑÀô¹Ò¤p²Õ²Õªø´£¥X¥R¤À²z¥Ñ¡A¨Ã¥Ñ¿W¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê¡AÃÒ©ú¨ä²Å¦XÀôºÊ¤â¥U©Ò¸ü³W©w¡A¨Ã´£¥æ¸pªø§åã¡C
5.5 All environmental monitoring and
audit data submitted under this Permit shall be true, valid and correct.
®Ú¾Ú¥»³\¥iÃÒ´£¥æªº©Ò¦³ÀôºÊ¼Æ¾Ú¡A§¡¶·¦³®Ä¤Î¯u¹êµL»~¡C
6. Electronic
Reporting of EM&A Information
ÀôºÊ¸ê®Æªº¹q¤l¶×³ø
6.1 To
facilitate public inspection of the monthly/quarterly EM&A Reports via the
EIAO Internet Website and at the EIAO Register Office, electronic copies of
these Reports shall be prepared in Hyper Text Markup Language (HTML) (version
4.0 or later) and in Portable Document Format (PDF version 1.3 or later),
unless otherwise agreed by the Director and shall be submitted at the same time
as the hardcopies as described in Condition 5 of this Permit. For the HTML
version, a content page capable of providing hyperlink to each section and
sub-section of these Reports shall be included in the beginning of the
document. Hyperlinks to all figures, drawings and tables in these Reports shall
be provided in the main text from where the respective references are made. All
graphics in these Reports shall be in interlaced GIF format unless otherwise
agreed by the Director. The content of the electronic copies of these Reports
must be the same as the hardcopies.
¬°¤è«K¤½²³³z¹LÀôµû±ø¨Ò¤¬Ápºôºô¯¸¤Î¦bÀôµû±ø¨Òµn°O¥U¿ì¨Æ³B¬d¾\¨C¤ë / ¨C©uÀôºÊ³ø§i¡A¥H¶W¤å¥»¼Ð¥Ü»y¨¥ (HTML) (²Ä4.0©Î¸û«áª©¥») ¤Î«KÄ⦡¤å¥ó®æ¦¡ (PDF) (²Ä1.3©Î¸û«áª©¥») »s§@ªº³ø§iªº¹q¤lª©¥»¡A°£«D¥tÀò¸pªø¦P·N¡A¶·»P¥»³\¥iÃÒ±ø¥ó²Ä5¶µ©Ò»¡©úªºµw½Æ¥»¦P®É´£¥æ¡CÃö©óHTMLªºª©¥»¤è±¡A¥i»P³ø§i¦U¸`¤Î¤p¸`§@¥X¶W¤å¥»³sµ²ªº¥Ø¿ý¶·¦b¤å¥ó¶}ºÝ¥[¤J¡C³ø§i¤º¦UÃþ¹Ïªí¶·¦b¸ü¦³¬ÛÃö¸ê®Æªº¥¿¤å¤º§@¥X¶W¤å¥»³sµ²¡C°£«D¥tÀò¸pªø¦P·N¡A³ø§i¤º©Ò¦³¹Ï§Î§¡¶·¥H¥æ¿ù¦s¨úªºGIF®æ¦¡¨î©w¡C³ø§iªº¹q¤lª©¥»¤º®e¡A¥²¶·»Pµw½Æ¥»ªº¤º®e¤@P¡C
6.2 The
Permit Holder shall, set up a dedicated website and notify the Director in
writing the Internet address where the environmental monitoring and project
data are to be placed, within six weeks after the commencement of construction
of the Project. All environmental monitoring data described in Condition 6.1 above
shall be made available to the public via a dedicated website to be set up by
the Permit Holder in the shortest possible time and in no event later than 2
weeks after the relevant environmental monitoring data are collected or become
available, unless otherwise agreed with the Director.
³\¥iÃÒ«ù¦³¤H¶·¦b¤uµ{¶µ¥Øªº«Ø³y¤uµ{®i¶}«á6Ó¬P´Á¤º¡A³]¥ß¯S©w¤¬Ápºôºô¯¸¦s©ñÀô¹ÒºÊ¹î¼Æ¾Ú¤Î¤uµ{¶µ¥Ø¸ê®Æ¡A¨Ã¥H®Ñ±³qª¾¸pªø¤¬Ápºôºô§}©Ò¦b¡C¤W¤å±ø¥ó²Ä6.1¶µ»¡©úªº©Ò¦³Àô¹ÒºÊ¹î¼Æ¾Ú¡A§¡¶·ºÉ§Ö³z¹L¥Ñ³\¥iÃÒ«ù¦³¤H³]¥ßªº¯S©wºô¯¸¨Ñ¤½²³¾\Äý¡A¦b¥ô¦ó±¡ªp¤U§¡¤£±o¿ð©ó¦³ÃöÀô¹ÒºÊ¹î¼Æ¾Ú¦¬¶°©Î¥i¨Ñ¾\Äý«áªº2Ó¬P´Á¡A°£«D¥tÀò¸pªø¦P·N¡C
6.3 The
Internet website as described in Condition 6.2 above shall enable user-friendly
public access to the monitoring and project data including the EIA Report and
the environmental permit(s) and the project profile of the Project. The
Internet website shall have features capable of:
(i)
providing
access to all environmental monitoring data collected since the commencement of
works;
(ii)
searching by date;
(iii)
searching by types of monitoring
data (air quality etc.); and
(iv)
hyperlinks to relevant monitoring
data after searching;
or otherwise as agreed by the
Director.
¤W¤å±ø¥ó²Ä6.2¶µ»¡©úªº¤¬Ápºôºô¯¸¡A¥²¶·¤è«K¥Î¤á¨Ï¥Î¡AÅý¤½²³®e©ö±µ¹FºÊ¹î¼Æ¾Ú¤Î¤uµ{¶µ¥Ø¸ê®Æ¡A·í¤¤¥]¬A¤uµ{¶µ¥ØªºÀôµû³ø§i¡BÀô¹Ò³\¥iÃҤΤuµ{¶µ¥Ø²¤¶¡C°£«D¥tÀò¸pªø¦P·N¡A¤¬Ápºôºô¯¸¶·¨ã³Æ³¡¥ó¡A´£¨Ñ¤Uz¥\¯à¡G
(i) ±µ¹F¤uµ{®i¶}«á©Ò¦¬¶°ªº¥þ³¡Àô¹ÒºÊ¹î¼Æ¾Ú¡F
(ii) «ö¤é´Á·j´M¡F
(iii) «öºÊ¹î¼Æ¾ÚÃþ§O (ªÅ®ð½è¯Àµ¥) ·j´M¡F¥H¤Î
(iv) ¦b·j´M«á»P¬ÛÃöªººÊ¹î¼Æ¾Ú§@¥X¶W¤å¥»³sµ²¡C
Notes:
µù¡G
1. This Permit consists
of three parts, namely, Part A (Main Permit), Part B (Description of Designated Project) and Part C (Permit Conditions). Any person relying on this permit should
obtain independent legal advice on the legal implications under the EIAO, and
the following notes are for general information only.
¥»³\¥iÃÒ¦@¦³3³¡¡A§YA³¡ (³\¥iÃÒ¥Dn³¡¤À)¡FB³¡ («ü©w¤uµ{¶µ¥Øªº»¡©ú) ¤ÎC³¡ (³\¥iÃÒ±ø¥ó)¡C¥ô¦ó´©¤Þ¥»³\¥iÃÒªº¤H¤h¶·´NÀôµû±ø¨Òªºªk«ß§t·N¼x¸ß¿W¥ßªk«ß·N¨£¡A¤Uzµù¸Ñ¥u¨Ñ¤@¯ë°Ñ¦Ò¥Î¡C
2. If there is a breach
of any condition of this Permit, the Director or his authorized officer may,
with the consent of the Secretary for the Environment, order the cessation of
associated work until the remedial action is taken in respect of the resultant
environmental damage, and in that case the Permit Holder shall not carry out
any associated works without the permission of the Director or his authorized
officer.
¦p¹H¤Ï¥»³\¥iÃÒªº¥ô¦ó±ø¥ó¡A¸pªø©ÎÀò±ÂÅv¤Hû¥i¦bÀô¹Ò§½§½ªøªº¦P·N¤U°Ç¥O°±¤î¬ÛÃö¤uµ{¡Aª½¦Ü³\¥iÃÒ«ù¦³¤H¬°©Ò³y¦¨ªºÀô¹Ò·l®`±Ä¨ú¸É±Ï¦æ°Ê¬°¤î¡C¦b¦¹±¡ªp¤U¡A³\¥iÃÒ«ù¦³¤H¥¼¸g¸pªø©ÎÀò±ÂÅv¤Hû¦P·N¡A¤£±o¶i¦æ¥ô¦ó¬ÛÃö¤uµ{¡C
3. The Permit Holder
may apply under Section 13 of the EIAO to the Director for a variation of the
conditions of this Permit. The Permit Holder shall replace the original permit
displayed on the Project site by the amended permit.
³\¥iÃÒ«ù¦³¤H¥i®Ú¾ÚÀôµû±ø¨Ò²Ä13±øªº³W©w¦V¸pªø¥Ó½Ð§ó§ï¥»³\¥iÃÒªº±ø¥ó¡C³\¥iÃÒ«ù¦³¤H¶·¥H¸g×qªº³\¥iÃÒ´À´«¦b¤uµ{¶µ¥Øªº¤u¦a¤º®i¥Üªºì¦³³\¥iÃÒ¡C
4. A person who assumes
responsibility for the whole or a part of the Project may, before he assumes
responsibility of the Project, apply under Section 12 of the EIAO to the
Director for a further environmental permit.
©Ó¾á¤uµ{¶µ¥Ø¾ã¶µ©Î³¡¤À¤uµ{ªº³d¥ôªº¤H¡A¦b©Ó¾á³d¥ô¤§«e¡A¥i®Ú¾ÚÀôµû±ø¨Ò²Ä12±øªº³W©w¦V¸pªø¥Ó½Ð·sªºÀô¹Ò³\¥iÃÒ¡C
5. Under Section 14 of
the EIAO, the Director may with the consent of the Secretary for the
Environment, suspend, vary or cancel this Permit. The suspended, varied or cancelled
Permit shall be removed from display at the Project site.
®Ú¾ÚÀôµû±ø¨Ò²Ä14±øªº³W©w¡A¸pªø¥i¦bÀô¹Ò§½§½ªøªº¦P·N¤U¼È®É¦Q¾P¡B§ó§ï©Î¨ú®ø¥»³\¥iÃÒ¡C¾D¼È®É¦Q¾P¡B§ó§ï©Î¨ú®øªºÀô¹Ò³\¥iÃÒ¥²¶·±q¤uµ{¶µ¥Øªº¤u¦a°£¤U¡A¤£¦A®i¥Ü¡C
6. If this Permit is cancelled
or surrendered during construction or operation of the Project, another
environmental permit must be obtained under the EIAO before the Project could
be continued. It is an offence
under Section 26(1) of the EIAO to operate a designated project listed in Part
I of Schedule 2 of the EIAO without a valid environmental permit.
¦p¥»³\¥iÃÒ¦b¤uµ{¶µ¥Ø«Ø³y©ÎÀç¿ì´Á¶¡¨ú®ø©Î¥æ¦^¡A«h¦bÄ~Äò¶i¦æ¤uµ{¶µ¥Ø¤§«e¡A¥²¶·¥ý®Ú¾ÚÀôµû±ø¨Ò³W©w¨ú±o¥t¤@¥÷Àô¹Ò³\¥iÃÒ¡C®Ú¾ÚÀôµû±ø¨Ò²Ä26(1)±øªº³W©w¡A¥ô¦ó¤H¦b¨S¦³¦³®ÄÀô¹Ò³\¥iÃÒªº±¡ªp¤UÀç¿ìÀôµû±ø¨Òªþªí2²ÄI³¡©Ò¦C©úªº«ü©w¤uµ{¶µ¥Ø¡A§YÄݥǸo¡C
7. Any person who
constructs or operates the Project contrary to the conditions in the Permit,
and is convicted of an offence under the EIAO, is liable:
(i)
on a first conviction on indictment
to a fine of $2 million and to
imprisonment for 6 months;
(ii)
on a second or subsequent
conviction on indictment to a fine of $5 million and to imprisonment for 2
years;
(iii)
on a first summary conviction to a
fine at level 6 and to imprisonment for 6 months;
(iv)
on a second or subsequent summary
conviction to a fine of $1 million and to imprisonment for 1 year; and
(v)
in any case where the offence is of
a continuing nature, the court or magistrate may impose a fine of $10,000 for
each day on which he is satisfied the offence continued.
¦p¥ô¦ó¤H¦b¹H¤Ï¥»³\¥iÃÒªº±ø¥ó¤U«Ø³y©ÎÀç¿ì¤uµ{¶µ¥Ø¡A®Ú¾ÚÀôµû±ø¨Ò¡A§YÄݥǸo¡G
(i)
¤@¸g´`¤½¶Dµ{§Çº¦¸©w¸o¡A¥i³B»@´Ú200¸U¤¸¤ÎºÊ¸T6Ó¤ë¡F
(ii) ¤@¸g´`¤½¶Dµ{§Ç²Ä¤G¦¸©Î¨ä«á¨C¦¸©w¸o¡A¥i³B»@´Ú500¸U¤¸¤ÎºÊ¸T2¦~¡F
(iii) ¤@¸g´`²©öµ{§Çº¦¸©w¸o¡A¥i³B²Ä6¯Å»@´Ú¤ÎºÊ¸T6Ó¤ë¡F
(iv) ¤@¸g´`²©öµ{§Ç²Ä¤G¦¸©Î¨ä«á¨C¦¸©w¸o¡A¥i³B»@´Ú100¸U¤¸¤ÎºÊ¸T1¦~¡F¥H¤Î
(v)
¦b¥ô¦ó±¡ªp¤U¦p¸Ó¸o¦æÄÝ«ùÄò©Ê½è¡Aªk°|©Îµô§P©x¥i´N¨ä«H¯Ç¸Ó¸o¦æ³sÄòªº¨C¤@¤Ñ¥t³B»@´Ú10,000¤¸¡C
8. The Permit Holder
may appeal against any condition of this Permit under Section 17 of the EIAO within
30 days of receipt of this Permit.
³\¥iÃÒ«ù¦³¤H¥i¦b±µÀò¥»³\¥iÃÒ«á30¤Ñ¤º¡A®Ú¾ÚÀôµû±ø¨Ò²Ä17±ø´N¥»³\¥iÃÒªº¥ô¦ó±ø¥ó´£¥X¤W¶D¡C
9. The Notes are for
general reference only and that the Permit Holder should refer to the EIAO for
details and seek independent legal advice.
¤Wzµù¸Ñ¥u¨Ñ¤@¯ë°Ñ¦Ò¥Î¡A±ýª¾¦³Ãö¸Ô±¡¡A³\¥iÃÒ«ù¦³¤H¶·°Ñ¾\Àôµû±ø¨Ò¤Î¼x¸ß¿W¥ßªk«ß·N¨£¡C
10. Occupational
safety and health issues are governed by the Occupational Safety and Health
Ordinance (Cap.509) and the Factories and Industrial Undertakings Ordinance
(Cap.59). The Permit Holder is advised to contact the Labour Department for
requirements relating to occupational safety and health issues.
¾·~¦w¥þ¤Î°·±d¨Æ©y¡A¨ü¾·~¦w¥þ¤Î°·±d±ø¨Ò (²Ä509³¹) ©M¤u¼t¤Î¤u·~¸gÀç±ø¨Ò
(²Ä59³¹) ©Ò³WºÞ¡C¦³Ãö¾·~¦w¥þ¤Î°·±d¨Æ©yªº³W©w¡A³\¥iÃÒ«ù¦³¤H©yÁpµ¸³Ò¤u³B¡C
11. The Permit
Holder is reminded to observe the Air Pollution Control Ordinance Specified
License requirements on the recycling activities, emission standards,
management, maintenance and monitoring.
³\¥iÃÒ«ù¦³¤H°È¶·¿í¦uªÅ®ð¦Ã¬VºÞ¨î±ø¨Ò¤º¹ï´`Àô¦A³y¬¡°Ê¡B¼o®ð±Æ©ñ¼Ð·Ç¡BºÞ²z¡Bºû׫O¾i¤ÎºÊ¹îªº«ü©úµP·Ó³W©w¡C
Environmental Permit No. EP-226/2005/G
Àô¹Ò³\¥iÃÒ½s¸¹ EP-226/2005/G
| ¹Ï 1 | ¹Ï 2 | ¹Ï 3 | ¹Ï 4 | ¹Ï 5 | ¹Ï 6 |
[ ªð ¦^ º ¶ ] / [ ªð ¦^ ¥D ¥Ø ¿ý ]
[Reproduced from Table 13.1 of the EIA Report
(Register No.: AEIAR-086/2005)]
[Âà¸ü¦ÛÀôµû³ø§iªí13.1 (µn°O¥U½s¸¹¡GAEIAR-086/2005)]
Recycling Process ´`Àô¦A³y¹Lµ{ |
Parameters °Ñ¼Æ |
|
Electronics ¹q¤l¹s¥ó Crush-and-sieve of fluorescent lamp À£¸H¤Î¿z¤Àº·¥ú¿O |
Stack height* ·Ï§w°ª«×* Stack diameter* ·Ï§wª½®|* Efflux velocity* ¼o®ð±Æ¥Xªº³t«×* Exit temperature* ¼o®ð±Æ¥X®Éªº·Å«×* Max. Permissible
Emission Rate (g/s) ³Ì°ª³\¥i±Æ©ñ²v (§J / ¬í) Mercury (Hg) ¤ô»È |
: : ¦a±¥H¤W : : : : ¨C¬í : : Äá¤ó23.5«× : 2.4167 ´ 10-6 |
Glass ¬Á¼þ Melting / forming and finishing of glass º²¤Æ / ¦¨§Î¤Î©ß¥ú |
Stack height* ·Ï§w°ª«×* Stack
diameter * ·Ï§wª½®| * Efflux velocity* ¼o®ð±Æ¥Xªº³t«×* Exit temperature* ¼o®ð±Æ¥X®Éªº·Å«×* Max. Permissible
Emission Rate (g/s) ³Ì°ª³\¥i±Æ©ñ²v (§J / ¬í) Particulate matter (PM) ²É¤l |
: : ¦a±¥H¤W : : : : ¨C¬í :
80OC : Äá¤ó80«× :
0.0202 |
Non-ferrous Metals ¦³¦âª÷ÄÝ Metal recovery (sweating, melting, refining) §âª÷ÄÝ´`Àô¦A³y (º²²k¡Bº²¤Æ¡Bºë·Ò) For Lot
EP11-01(2), refer to Condition No. 4.15, Annex C and Figure 5. |
Stack height*^ ·Ï§w°ª«×*^ Stack
diameter *^ ·Ï§wª½®|*^ Efflux velocity*^ ¼o®ð±Æ¥Xªº³t«×*^ Exit temperature*^ ¼o®ð±Æ¥X®Éªº·Å«×*^ Max. Permissible Emission Rate (g/s) ³Ì°ª³\¥i±Æ©ñ²v (§J / ¬í) PM²É¤l Sulphur dioxide (SO2) ¤G®ñ¤Æ²¸ Chlorine (Cl2) ´â Hydrogen chloride (HCl) ´â¤Æ²B Fluorine/Fluoride (F) ¬t / ¬t¤Æª« White Phosphorus (P) ¥ÕÁC Lead (Pb) ¹] Beryllium (Be) ¹e Cadmium (Cd) Âð Mercury (Hg) ¤ô»È Nickel (Ni) Âì Arsenic (As) ¯~ Tin (Sn) ¿ü Molybdenum (Mo) à» Copper (Cu) »É Antimony (Sb) ¾O Chromium VI (Cr 6+)¤»»ù»Ì Platinum (Pt) ¹` Selenium (Se) Ö´ Rhodium (Rh) ä{ |
: : ¦a±¥H¤W : : : : ¨C¬í : 80OC : Äá¤ó80«× : 0.0407 : 1.5432 : 0.0177 : 0.3550 : 0.0444 : 0.0081 : 0.0389 : 1.63 ´ 10-6 : 0.0008 : 0.0008 : 0.0081 : 0.0016 : 0.0122 : 0.0081 : 0.0163 : 0.0041 : 3.58 ´ 10-5 : 0.0016 : 0.0016 : 0.0008 |
Plastic ¶ì½¦ Moulding and extrusion À½¼Ò¤ÎÀ½À£ |
Stack
height* ·Ï§w°ª«×* Stack
diameter* ·Ï§wª½®|* Efflux velocity* ¼o®ð±Æ¥Xªº³t«×* Exit temperature* ¼o®ð±Æ¥X®Éªº·Å«×* Max. Permissible
Emission Rate (g/s) ³Ì°ª³\¥i±Æ©ñ²v (§J / ¬í) PM²É¤l |
: : ¦a±¥H¤W : : : : ¨C¬í : 23.5OC Äá¤ó23.5«× : 8.9580 ´ 10-3 |
Rubber Tyres ¾ó½¦½üL Grinding ¬ã¿i |
Stack
height* ·Ï§w°ª«×* Stack
diameter * ·Ï§wª½®|* Efflux velocity* ¼o®ð±Æ¥Xªº³t«×* Exit temperature* ¼o®ð±Æ¥X®Éªº·Å«×* Max. Permissible
Emission Rate (g/s) ³Ì°ª³\¥i±Æ©ñ²v (§J / ¬í) PM²É¤l |
: : ¦a±¥H¤W : : : : ¨C¬í : 23.5OC : Äá¤ó23.5«× : 9.1986 ´ 10-3 |
Wood ¤ì§÷ Plastic-wood composite manufacturing (extruding) ¥[¤u¥Í²£²V¦X¶ì½¦¤Î¤ì§÷ªº§¨ªO (À½À£) |
Stack
height* ·Ï§w°ª«×* Stack
diameter * ·Ï§wª½®|* Efflux velocity* ¼o®ð±Æ¥Xªº³t«×* Exit temperature* ¼o®ð±Æ¥X®Éªº·Å«×* Max. Permissible
Emission Rate (g/s) ³Ì°ª³\¥i±Æ©ñ²v (§J / ¬í) PM ²É¤l |
: : ¦a±¥H¤W : : : : ¨C¬í : 23.5OC : Äá¤ó23.5«× : 8.9580 ´ 10-3 |
Fuel Combustion Emissions ¿U®Æ¿U¿Nªº¼o®ð±Æ©ñ |
Parameters °Ñ¼Æ |
|
|
Stack
height*^ ·Ï§w°ª«×*^ Stack
diameter *,^ ·Ï§wª½®|*^ Efflux velocity*,^ ¼o®ð±Æ¥Xªº³t«×*^ Exit temperature* ¼o®ð±Æ¥X®Éªº·Å«×* §t²¸¶q |
: : ¦a±¥H¤W : : : : ¨C¬í : 80OC : Äá¤ó80«× : £ 0.005% sulphur by weight : «ö«¶qp§t²¸¶q£ 0.005% |
Max. Permissible
Emission Rate (g/s) ³Ì°ª³\¥i±Æ©ñ²v (§J / ¬í) PM²É¤l SO2¤G®ñ¤Æ²¸ Nitrogen oxides (NOx) ´á®ñ¤Æª« Carbon monoxide (CO) ¤@®ñ¤ÆºÒ |
: 0.5000 : 0.1963 : 6.0000 : 1.2500 |
Note: µù: |
* ^ |
These values are minimum values
to be achieved if the planned holiday camp to be north of the Project site
(as shown in Figure 1) is not
developed. However, if the
holiday camp is occupied, these values are to be exact values to be achieved. ¦p¤w³W¹º³]©ó¤uµ{¶µ¥Ø¤u¦a¥_±ªº«×°²Àç (¹Ï1©Ò¥Ü) ¤£·|µo®i¡A«h¤Wz¼ÆȬ°¥²¶·¹F¨ìªº³Ì§C¼ÆÈ¡C¦ý¬O¡A¦p«×°²À禳¤H¦û¥Î¡A¤Wz¼ÆÈ«K¬°¥²¶·¹F¨ìªº½T¤Á¼ÆÈ¡C These values are not applicable to Lot EP11-01(2) of
which values are specified in Condition No. 4.15. ¤Wz¼ÆȤ£¾A¥Î©óEP11-01(2)¦a¬q¡A¦³Ãö¦a¬qªº¼ÆȦb²Ä4.15¶µ±ø¥óµù©ú¡C |
|
|
|
|
|
|
ªþ¥óB (±ø¥ó²Ä4.10¶µ©Òz)
¤uµ{¶µ¥Ø¤u¦a¤ºªº«Ø¿vª«°ª«×¨î
Distance (D) of Building from the Western Boundary
of the Project Site (m) ¥Ñ¤uµ{¶µ¥Ø¤u¦a¦è±¬É½u°_p |
Maximum Height (H) of Building (where people work
at elevated levels) (m) «Ø¿vª«ªº°ª«×¤W |
0 |
0 |
5 |
6 |
10 |
13 |
20 |
26 |
30 |
39 |
40 |
52 |
50 |
66 |
Annex C (as referred to in
Condition 4.15)
ªþ¥óC (±ø¥ó²Ä4.15¶µ©Òz)
i Air
Pollution Control Measures for the Plant
¼t©ÐªºªÅ®ð¦Ã¬VºÞ¨î±¹¬I
a)
Other
than complying with permit conditions as stated below, the plant shall comply with
other environmental legislation including but not limited to the Air Pollution
Control Ordinance Cap 311.
°£²Å¦X¤Uzªº³\¥iÃÒ±ø¥ó¥~¡A¼t©Ð¶·²Å¦X¨ä¥LÀô«O±ø¨Ò¥]¬A¦ý¤£©óªÅ®ð¦Ã¬VºÞ¨î±ø¨Ò(²Ä311³¹)
Plant Layout and Operation Duration
¼t©Ðªº§G§½¤ÎÀç¿ì®É¶¡
b)
The
recycling process shall be conducted within an enclosed building in the Lot
EP11-01(2) as shown in Figure 5. The
enclosed building shall be maintained under negative pressure during operation
of the plant.
´`Àô¦A³y¤u§Ç¶·©ó¹Ï5©Ò¥Ü¦a¬qEP11-01(2)¤ºªº³ò«Ê¦¡«Ø¿vª«¤º¶i¦æ¡C·í¼t©ÐÀç¿ì®É, ³ò«Ê¦¡«Ø¿vª«¤º¶·³B©ótÀ£ª¬ºA¡C
c)
Only
one set of
stack shall be designed and operated for the exhaust gas from smelting process
for the plant. The location point is EP1 as shown in Figure 5
¼t©Ð¦b³]p¤W¥u¯à³]¸m¤ÎÀç¿ì¤@²Õ·Ï§w¡A¨Ñ±Æ©ñ§M·Ò¤u§Çªº¼o®ð¡C¸Ó¦aÂIEP1¦p¹Ï5©Ò¥Ü¦ì¸m¡C
d)
To
minimize the air quality impact, no stack emissions associated with the
operation of the project shall be allowed between 1900 to 0700 hours daily.
¬°´î¤Ö¹ïªÅ®ð½è¯À³y¦¨ªº¼vÅT¡A¨C±ß7®É¦Ü²Ý±á7®É¤§¶¡¡C
Control of Process and
Equipment
¤u§Ç¤Î³]³ÆªººÞ¨î
e)
The dismantling of the spent batteries shall be conducted within an
enclosed chamber fitted with an exhaust system. The exhaust system shall be connected
to a properly
maintained wet scrubber for the
removal of acidic mist before discharging into the atmosphere. The
concentration level of H2SO
©î°£¼o¹q¦À¶·©ó³]¦³©â·¨t²Îªº³ò«Ê¦¡ªÅ¶¡¤º¶i¦æ¡C¨ä±Æ©â·¨t²Î¶·³s±µ§´µ½«O¾iªºÀ㦡¬~º°¾¹¡A¥H«K²M°£»ÄÃú¡A¥O±Æ©óªÅ®ð¤¤²¸»Ä¿@«×§C©ó¨C¼Ð·Ç¥ß¤è¦Ì1²@§J¡C
f)
For the purpose of reduction of sulphur dioxide (SO2) emission from the plant, lead paste collected from
the spent batteries shall undergo chemical desulphurization prior to entry to
the rotary tilting furnace for the smelting process. The details of the chemical
desulphurization shall be deposited in the compliance audit report under part (iii) of this Annex.
¬°´î¤Ö¼t©Ðªº¤G®ñ¤Æ²¸±Æ©ñ¶q¡A±q¼o¹q¦À¦¬¶°©Ò±oªº¹]»I¡A¦b¶i¤J±ÛÂà¶É±×Äl¶i¦æ§M·Ò¤u§Ç«e¡A¶·¸g¹L¤Æ¾Ç²æ²¸µ{§Ç¡C¦Ó¤Æ¾Ç²æ²¸µ{§Çªº¸Ô²Ó¸ê®Æ¶·¦s©ñ©ó¥»ªþ¥ó²Ä(iii)¬qªº²Å¦X³W©w¼f®Ö³ø§i¡C
g)
No more than 2 rotary tilting furnaces shall be installed
in the plant for smelting process or otherwise as approved by the Director.
°£¸g¸pªø§åã¥~¡A¼t©Ð¤º¤£¥i³]¦³¦h©ó2Ó±ÛÂà¶É±×Äl§@¬°§M·Ò¤u§Ç¡C
h)
For the control of nitrogen oxides (NOx) emission at the rotary tilting
furnaces, oxy-fuel burners shall be used.
The details of the
oxy-fuel burners shall be deposited in the compliance audit report under part (iii) of this Annex.
¬°±±¨î±ÛÂà¶É±×Älªº´á®ñ¤Æª«±Æ©ñ¶q¡A±ÛÂà¶É±×Äl¶·¨Ï¥Î¥H®ñ®ð¿U®Æ¿U¿N¾¹¡C¦Ó®ñ®ð¿U®Æ¿U¿N¾¹ªº¸Ô²Ó¸ê®Æ¶·¦s©ñ©ó¥»ªþ¥ó²Ä(iii)¬qªº²Å¦X³W©w¼f®Ö³ø§i¡C
i)
For
the control of sulphur dioxide (SO2) emission from the plant,
biodiesel or other cleaner fuel(s) shall be used, either of which shall have
sulphur content no greater than 0.005% weight per weight.
¬°±±¨î¼t©Ðªº¤G®ñ¤Æ²¸±Æ©ñ¶q¡A¶·¨Ï¥Î§t²¸¶q¤£¦h©ó0.005%¡]«¶q¦Ê¤À¤ñ¡^ªº¥Íª«®ãªo©Î¨ä¥L¸û§C¦Ã¬V¿U®Æ¡C
Control of Emission from
Baghouse Filtration System
³U¦¡¹jÂo¨t²Îªº±Æ©ñºÞ¨î
j)
Emissions from smelting process including those emissions from the
rotary tilting furnaces and the oxy-fuel burner shall be treated by the baghouse filtration system
before emitting at EP1.
§M·Ò¤u§Ç±Æ©ñªº¼o®ð¥]¬A¥Ñ±ÛÂà¶É±×Älªº±Æ©ñ¤Î®ñ®ð¿U®Æ¿U¿N¾¹ªº±Æ©ñ¥²¶·¥ý¥H³U¦¡¹jÂo¨t²Î³B²z¡A¦A¸g¥ÑEP1±Æ¥X¡C
k)
Fugitive air pollutants
generated other than from smelting process shall be treated by the baghouse
filtration system before emission at designated location(s) with details to be
deposited with the Director.
°£§M·Ò¤u§Ç¥~¡A°k¶h©ÊªÅ®ð¦Ã¬Vª«©ó«ü©w±Æ©ñ³B±Æ¥X«e¡A¥²¶·¥ý¥H³U¦¡¹jÂo¨t²Î³B²z¡A¦Ó«ü©w±Æ©ñ³Bªº¸ê®Æ¶·¦V¸pªø¦s¥æ¡C
l)
For the proper operation of the plant, a baghouse filtration system shall
be installed. The baghouse filtration system shall have dust removal efficiency
of no less than 99.9% to remove dust and suspended lead particles. It shall
also be equipped and operated with a self-cleaning system using jet blasts to
remove the accumulated dust to maintain its function.
¼t©Ð¦bÀç¿ì®É¶·³]¸m³U¦¡¹LÂo¨t²Î¡C³U¦¡¹LÂo¨t²Îªº°£¹Ð®J©M§t¹]ªºÄa¯B²É¤l®Ä²v¶·¤£§C©ó99.9%¡C¦¹¨t²Î¶·°t³Æ©M¨Ï¥Î¦Û²b¨t²Î¡A³z¹L¼Q¬y¤è¦¡²M°£¿n»Eªº¹Ð®J¡A¥Hºû«ù¨ä¥\¯à¡C
Control of Emission from
Stacks
·Ï§wªº±Æ©ñºÞ¨î
m)
For
EP1, from the
smelting process, the diameter of the stack shall be 1.8 m or otherwise as
approved by the Director.
°£¸g¸pªø§åã¥~¡A§M·Ò¤u§Ç±Æ©ñÂIEP1¡A¨ä·Ï§wª½®|¶·¬°1.8¦Ì¡C
n)
Stack at EP1 for the plant shall have a stack tip at 30m above ground or
otherwise as approved by the Director.
°£¸g¸pªø§åã¥~¡A¼t©Ðªº·Ï§w©óEP1°ª«×¶·¬°¥D¤ô¥°ò·Ç¥H¤W30¦Ì(¥Ñ·Ï§w³»³¡¶q«×)¡C
o)
The
efflux velocity for exhaust gas at EP1 shall be no less than 16.9m/s or otherwise as
approved by the Director.
°£¸g¸pªø§åã¥~¡AEP1ªº±Æ®ð³t«×¤£±o§C©ó¨C¬í16.9¦Ì¡C
p)
The
exit temperature for exhaust gas at EP1 shall not be less than 80oC or
otherwise as approved by the Director.
°£¸g¸pªø§åã¥~¡AEP1±Æ®ð®Éªº·Å«×¤£±o§C©óÄá¤ó80«×¡C
q)
The
maximum emission rates of the pollutants at EP1 shall not exceed those as
stated in the table below or otherwise as approved by the Director:
°£¸g¸pªø§åã¥~¡AEP1 ªº³Ì°ª¦Ã¬Vª«±Æ©ñ²v¤£±o¶W¹L¤Uªí©Òz¡G
Emission
Point ±Æ©ñÂI |
Maximum
Emission Rate (gram per second (g/s)) ³Ì°ª¦Ã¬Vª«±Æ©ñ²v (§J/¬í) |
|||
Lead
(Pb) ¹] |
PM
²É¤l |
Nitrogen oxides (NOx) ´á®ñ¤Æª« |
Sulphur dioxide (SO2) ¤G®ñ¤Æ²¸ |
|
EP1 |
0.0085 |
0.034 |
0.99 |
0.46 |
ii On-Site
Wastewater Control Measures for the Plant
¼t©Ð¶·±Ä¨úªº²{³õ¼o¤ôºÞ¨î±¹¬I
a)
For
water pollution control, an on-site wastewater treatment plant shall be
provided and properly operated to treat all trade effluent and any heavy metal
containing precipitates/solutions before its discharge into the internal
sewerage at EcoPark. The effluent discharge from the on-site wastewater
treatment plant shall not exceed
¬°¤F±±¨î¤ô¦Ã¬V¡A¼t©Ð¶·´£¨Ñ¨Ã§´µ½¾Þ§@¤@Ó²{³õ¼o¤ô³B²z¸Ë¸m¡A¥H«K³B²z©Ò¦³¤u°Ó·~¦Ã¤ô¤Î¥ô¦ó§t«ª÷Äݪº¨I¾ýª«¡þ·»²G¡A¦A±N¼o¤ô±Æ¤JÀô«O¶é¤ºªº¦Ã¤ô´ë¡C±q²{³õ¼o¤ô³B²z¸Ë¸m±Æ¥Xªº¦Ã¤ô¨C¤Ñ¤£±o¶W¹L
iii Compliance Audit
Report
²Å¦X³W©w¼f®Ö³ø§i
a) The Permit Holder shall, at least 6 weeks before the operation of the plant, notify the Director in writing of the commencement of operation.
³\¥iÃÒ«ù¦³¤H¶·¦b¼t©ÐÀç¿ì«e¡A¦Ü¤Ö´£¦6Ó¬P´Á¥H®Ñ±³qª¾¸pªø¼t©Ð¶}©lÀç¿ìªº¤é´Á¡C
b) To ensure the findings and mitigation measures as detailed in the report submitted under the application for variation of environmental permit No.VEP-494/2016 are complied with, the Permit Holder shall prepare a compliance audit report detailing the implementation and the design standards of the mitigation measures, and an operational air monitoring plan. After being certified by the ET Leader and verified by the IEC, both submissions shall be deposited with the Director at least one month prior to operation of the plant.
¬°½T«OÀH§ó§ïÀô¹Ò³\¥iÃÒ(½s¸¹:VEP-494/2016)ªº¥Ó½Ð®Ñ»¼¥æªº³ø§i©Ò¸Ôzªºµ²ªG¤Î½w¸Ñ±¹¬I±o¨ì¿í¦æ¡A³\¥iÃÒ«ù¦³¤H¶·´£¥æ²Å¦X³W©w¼f®Ö³ø§i¡A¸Ô¦C¦³Ãö½w¸Ñ±¹¬Iªº¹ê¬I±¡ªp¤Î³]p¼Ð·Ç¤Î¹B§@´ÁªÅ®ðºÊ´úp¹º®Ñ¡C¦b¼t©ÐÀç¿ì«e¦Ü¤Ö1Ó¤ë¡A³ø§i¸gÀô¹Ò¤p²Õ²Õªø®ÖÃҤοW¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê«á¡A¶·¦V¸pªø¦s¥æ¡C
c) The Permit Holder shall carry out 2 years of operational air quality monitoring or for a duration as agreed by the Director in accordance with the deposited monitoring plan.
³\¥iÃÒ«ù¦³¤H¶·«ö·Ó¤w¦s¥æªººÊ´úp¹º®Ñ¶i¦æ¹B§@´ÁªÅ®ð½è¯ÀºÊ´ú¡A¬°´Á¨â¦~©Î¸pªø¦P·Nªº«ùÄò®É¶¡¡C
Annex D (as referred to in Condition 4.16)
ªþ¥óD (±ø¥ó²Ä4.16¶µ©Òz)
Cathode Ray Tube (CRT) Recovery Process
³±·¥®g½uºÞªº¦^¦¬µ{§Ç
a) The process of CRT dismantling and crushing shall be carried out in enclosed structure(s). All fugitive air pollutants including dust and suspended lead, mercury and phosphorous particles shall be extracted by localized hood/ extraction system for removing/filtering the air pollutants prior to discharge. The operation details and removal efficiency of the extraction and associated filter systems shall be certified by the ET Leader and verified by the IEC prior to operation.
©î°£¤ÎÀ£¸H³±·¥®g½uºÞªºµ{§Ç¥²¶·©ó³ò«Ê¦¡«Ø¿vª«¤º¶i¦æ¡A©Ò¦³°k¶h©ÊªÅ®ð¦Ã¬Vª«¥]¬A¹Ð®J©M§t¹]¡B¤ô»È¤ÎÁCªºÄa¯B²É¤l¡A¥²¶·©â¦Ü©â·¨t²Î²M°£/¹LÂo«á¡A¤~±Æ©ñ¦Ü¤j®ð¤¤¡C©â·¤Î¬Û³sªº¹LÂo¨t²Îªº¾Þ§@²Ó«h¤Î°£¹Ð®Ä²v¶·¸gÀô¹Ò¤p²Õ²Õªø®ÖÃҤοW¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê«á¡A¤è¥iÀç¿ì¡C
b)
Chemicals used in the CRT glass
washing process shall be re-circulated. Non- recyclable or spent chemicals from
the process shall be disposed of to the Chemical Waste Treatment Centre or by a
method to be certified by the ET Leader and verified by the IEC.
¥Î©ó²M¬~³±·¥®g½uºÞ¬Á¼þµ{§Çªº¤Æ¾Çª«¥²¶·´`Àô¨Ï¥Î¡Aµ{§Ç¤¤¤£¯à´`Àô©Î¼o¤Æ¾Çª«¶·¸g¤Æ¾Ç¼oª«³B²z¤¤¤ß³B¸m©Î¸gÀô¹Ò¤p²Õ²Õªø®ÖÃҤοW¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê«áªº¤èªk³B¸m¡C
Compliance
Audit Report
²Å¦X³W©w¼f®Ö³ø§i
i. The Permit Holder shall, at least 6 weeks before the operation of the plant, notify the Director in writing of the commencement of operation.
³\¥iÃÒ«ù¦³¤H¶·¦b¼t©ÐÀç¿ì«e¡A¦Ü¤Ö´£¦6Ó¬P´Á¥H®Ñ±³qª¾¸pªø¼t©Ð¶}©lÀç¿ìªº¤é´Á¡C
ii. To ensure the findings and mitigation measures as detailed in the report submitted under the application for variation of environmental permit No.VEP-408/2013 are complied with, the Permit Holder shall prepare a compliance audit report detailing the implementation and the design standards of the recycling facility and its mitigation measures. After being certified by the ET Leader and verified by the IEC, the compliance audit report shall be deposited with the Director at least one month prior to operation of the plant.
¬°½T«OÀH§ó§ïÀô¹Ò³\¥iÃÒ(½s¸¹:VEP-408/2013)ªº¥Ó½Ð®Ñ»¼¥æªº³ø§i©Ò¸Ôzªºµ²ªG¤Î½w¸Ñ±¹¬I±o¨ì¿í¦æ¡A³\¥iÃÒ«ù¦³¤H¶·´£¥æ²Å¦X³W©w¼f®Ö³ø§i¡A¸Ô¦C¦³Ãö¦^¦¬³]¬I¤Î½w¸Ñ±¹¬Iªº¹ê¬I±¡ªp¤Î³]p¼Ð·Ç¡C¦b¼t©ÐÀç¿ì«e¦Ü¤Ö1Ó¤ë¡A³ø§i¸gÀô¹Ò¤p²Õ²Õªø®ÖÃҤοW¥ßÀô¹Ò¬d®Ö¤H®Ö¹ê«á¡A¶·¦V¸pªø¦s¥æ¡C
Annex E (as referred to in Scale
and Scope of Designated Project in Part B)
ªþ¥óE (B³¡ªº«ü©w¤uµ{¶µ¥Øªº³W¼Ò©M½d³ò©Òz)
Material Type ª«®ÆºØÃþ |
Total Annual Throughput Limits (tpa) ¨C¦~Á`¥Í²£¶qªº¨î (¤½¾·/¦~) |
Batteries
¹q¦À |
56,100 |
Electronics¹q¤l¹s¥ó |
63,880 |
Glass¬Á¼þ |
42,680 |
Organic
Food Waste ¦³¾÷¼p¾l |
82,180 |
Ferrous
Metals ÅKÃþª÷ÄÝ |
400,944
|
Non-ferrous
Metals¦³¦âª÷ÄÝ |
57,100 |
Paper¯È±i |
1,000,000 |
Plastics¶ì½¦ |
102,740 |
Textiles
¯¼Â´«~ |
8,010 |
Rubber
Tyres¾ó½¦½üL |
20,020 |
Wood¤ì§÷ |
41,260 |
Spent
Copper Etchant ¼o»É®û»k¾¯ |
3,290 |
Construction
Waste«Ø¿v¼oª« |
120,000 |
Lube
Oil ¼í·Æªo |
360 |
Annex F (as referred to in Condition 4.17)
ªþ¥óF (±ø¥ó²Ä4.17¶µ©Òz)
Waste Paper Recycling Process
¼o¯Èªº¦^¦¬µ{§Ç
i Air
Pollution Control Measure for the Plant
¼t©ÐªºªÅ®ð¦Ã¬VºÞ¨î±¹¬I
a) Unless otherwise approved by the Director upon the submission of a detailed proposal, no fuel combustion is allowed for the waste paper recycling process.
°£«D©Ò´£¥æªº¸Ô²Óij®×¥tÀò¸pªø§åã¡A¼o¯È¦^¦¬ªºµ{§Ç¤¤¤£¥i¶i¦æ¿U®Æ¿U¿N¡C
ii. Mitigation
Measure for Visual Impact for the Plant
¼t©Ðªºµøı½w¸Ñ±¹¬I
a) The height of the building shall not exceed 35m above the mean formation level of the site.
«Ø¿vª«ªº°ª«×¤£±o°ª©ó¥§¡¦a½L¥¾ã¤ô¥¥H¤W35¦Ì¡C